FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 1023

PDF page 1023 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1023
AC 27-1B · 1023Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                                  AC 27-1B, Chg 7


                      (2) The rest of the displayed information format should allow for easy assessment
and interpretation by the pilot.

                      (3) Overlays of TCAS, HTAWS, or weather information should not interfere with the
use of the ND for primary navigation tasks. There should be definition of the prioritization of overlay pop­
ups, if installed.

         (6) Powerplant and Systems Information.

                  (i) Powerplant. EDS display suites may or may not include the capability of displaying
powerplant parameters required by § 27.1305 along with electrical system information required by
§ 27.1351. Displaying powerplant information on a single display, as opposed to displaying the
information in separate gauges, decreases the independence of information. As a result, EDS
powerplant display (EICAS, IIDS, etc.) design should be robust enough so that information availability and
validity is commensurate with the assessed FHA failure condition classification.

                (A) Arrangement.

                      (1) 14 CFR 27.1321 and Appendix B to Part 27 (VIII) specify placement of
information relative to the pilot’s field of view. Refer to sections 27.1321 and 27.1305 and Appendix B of
this AC for further guidance.

                      (2) Torque, power turbine temperature, power turbine speed, main rotor speed, and
free turbine speed should continuously display in the pilot’s primary field of view. The format for these
parameters can vary and is discussed below.

                      (3) Display of engine oil temperature and pressure and main gearbox oil temperature
(and pressure if required) should continuously display.  If positioned in the pilot’s secondary field of view,
they should be as close to the pilot’s primary field of view as possible.

                (B) Format. EDS provides the ability to display powerplant information in a variety of
formats. For EDS installed to replace analog gauges, the format of the primary powerplant instruments
(TQ, N1, TGT) should allow pilots to easily transition from the old analog variant to the digital variant
without undue concentration and without training.

                      (1) Gauge layout and marking should be easy to see and interpret.

                                     (i) If using a similar format such as round-dial representation of a round dial
analog gauge, then indices and markings should be similar to the analog gauge the digital display is
replacing. This is to ensure there is no negative transfer from reading traditional electromechanical
gauges or confusion when reading the digital gauge. There may be improvements made over the
existing gauges. For example, an instrument such as a dual tachometer, which provides information on
the status of main rotor speed, may also provide information relating to pilot collective input (to correct a
deviation in rotor RPM). For example, providing a dual tachometer that places the normal range at the
9:00 position provides the pilot with two types of information.  If the rotor RPM is high, the needle is high.
It also gives the pilot a cue that to lower the RPM, the pilot should lower the collective to lower the NR
(and bring the needle down to the normal range).

                                       (ii) Use of a distinctly different format such as a tape or linear gauge or a
distinctly different shaped representation should allow for quick and easy assessment of information. The
ease of use should be better or the same upon gauge replacement.

                                         (iii) Needles, pointers, or other indicator means should point at the value, not
cross or obscure the value.  If using multiple needles or pointers on a display, the parameter that they are
indicators for should be clear and easily distinguishable from the others on the display.



                                                                   Page MG 19 - 21

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →