Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Extracted text for finding words
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 7 2/4/2016
(ii) Display of Global Navigation Satellite System (GNSS) altitude. The
simultaneous display of GNS and barometric altitude is not recommended. If there is a mode to display
GNSS or GPS derived altitude, the display of GPS altitude should be distinctly different from barometric
altitude so there can be no confusion regarding the source. Additionally, there should be clear labeling of
the GNSS altitude. One acceptable label is “GSL.”
(iii) Radar or radio altitude (RALT). RALT is required for certain operations. If
the integrated display system has the ability to provide RALT displays, there should be consideration
given to the intended function of the RALT in rotorcraft. A strictly numerical readout of RALT may not be
sufficient to provide the intended function based on operations. Conversely, a graphical display of RALT,
depending on the implementation, may create confusion. For example, incorporating a ground reference
cue based on RALT into a barometric altitude display could lead to confusion if not supplemented by
another cue.
(iv) The use of moving tape displays or graphical representation of traditional
round dial altimeters has been equally effective. Linear tape altimeter displays should include
enhancements denoting standard 500 and 1,000-foot increments, and they should convey the present
altitude unambiguously and at a glance. The combination of altimeter scale length and markings,
therefore, should be adequate to allow sufficient resolution for precise manual altitude tracking in level
flight, as well as enough scale length and markings to reinforce the pilot’s sense of altitude. The scale
length should also allow sufficient look-ahead room to adequately predict and accomplish level off. Pilot
evaluations have shown that, in addition to the appropriate altitude markings commensurate with
rotorcraft performance, the recommended use of an altitude reference bug provides acceptable cues.
(A) A trend indicator should be displayed unless a vertical speed indicator
(VSI) is located adjacent to the altimeter. A six-second altitude-trend indicator is typical, but other trend
values may be more appropriate depending on the rotorcraft performance and altitude tape scaling.
(B) Some operations require an instantaneous VSI. If installed, ensure it
functions correctly and provides the pilot with usable information. Some instantaneous VSI installations
may be unusable due to jittery performance.
(ii) Navigation. The navigation display (ND) portion of the PFD and a MFD can display
navigation information. This section focuses on the navigation information displayed on the navigation
display portion of the PFD. Guidance on information presented on the navigation display is contained in
SAE ARP 4102-7. Appendix B to SAE ARP 4102-7 provides navigation symbology guidance. Certain
information should also be included on the ND. Navigation source (GPS, VOR1, LOC, etc.), waypoint
name, and distance-to are types of information the ND should display, particularly if envisioning RNAV
approaches. ND displays have also contained primary powerplant information either as individual
instruments (torque (TQ), turbine temperature (TOT), or turbine speed (Ng, N1 %RPM)) or as an
integrated first limit indicator or power indicator display. Additionally, main rotor RPM (NR), and free
turbine speed (Np, NF, N2 %RPM) may be displayed on the ND.
(A) Arrangement.
(1) Normally, the HSI/compass rose is in the middle of the ND with the other
information arrayed around it.
(2) Active navigation information (waypoint name, etc.), should be as close to the top
of the display as possible to minimize the pilot’s scan between the PFD and ND.
(B) Format.
(1) The HSI/compass rose format should have a full 360o display. If an arc feature is
included, the arc should display at least 120o of heading. In arc mode, if the heading bug is off the
display, there should be a means to indicate to the pilot what heading the bug is set on.
Page MG 19 -20