Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/4/2016 AC 27-1B, Chg 7
and Appendix B to part 27, if applicable. There should be clustering and arrangement of the
electromechanical standby instruments to allow the pilot use of them without undue concentration.
(ii) Gyroscopic pitch and bank ADI presentation should meet the requirements of
§ 29.1303(g)(1) regardless of whether or not they are considered standby ADIs. Appendix B of this AC
and AC29-2, section 29.1303 explains the requirements for an ADI to comply with § 29.1303(g)(1).
(B) Arrangement.
(1) 14 CFR 27.1321 specifies placement of information relative to the pilot’s field of
view. Refer to section 27.1321 of this AC for further guidance.
(2) Most EDS displays follow the traditional “T” arrangement described in Appendix B
of this AC and § 29.1303. Deviations from this arrangement should be coordinated early with the
certification authority.
(3) Depending on design, addition of information normally found on EICAS or other
MFDs, such as power instruments or CAS messages, may be included. If this is the case, early human
factors evaluation for clutter, information density, and format and function of non-flight information should
be accomplished on bench tests and in a simulator (if available) or on in-flight evaluations.
(C) Format and function.
(1) Display of Attitude:
(i) Most EDS displays format attitude in a conventional manner. Alternate display
formats and functions considered should be coordinated early with the CA. Pitch, bank, horizon line and
indicators, and the rotorcraft symbol should be clear and easily acquired to allow the pilot quick access to
the rotorcraft’s attitude in all operating conditions. Regardless of added guidance or navigation cues,
there should still be the ability for the accurate assessment of the attitude by the pilot.
(ii) Some VFR at night operational rules require an attitude indicator. As a result,
depending on whether the rotorcraft is VFR or IFR certificated, the design assurance level of the EDS
PFD should be commensurate with the assessed FHA failure condition classification for loss of and
misleading attitude information. In addition, flight at night in a VFR rotorcraft, especially one without a
stabilization system, may require a higher failure condition classification than for day VFR.
(iii) Operational rules also require that VFR rotorcraft have an ADI for night
operations. If an ADI is required, it must meet and be installed in accordance with § 29.1303. Appendix
B and section 29.1303 of this AC explains the requirements for an ADI to comply with
14CFR 29.1303(g)(1).
(iv) Additional considerations. When the true horizon is no longer on the display,
the artificial horizon line should provide a distinctive demarcation between sky and ground (or the
background). The horizon reference line on the PFD should be at least 3.25 inches wide in straight and
level flight for integrated displays. This recommendation does not prevent replacement of mechanical
instruments with electronic displays of similar horizon reference line.
(2) Display of Altitude.
(i) Consider primary display of altitude to be barometric altitude. The altitude
display format should be clear and easily interpreted by the pilot. If the EDS allow selection of alternate
display modes such as switching between feet and meters, then clearly display the active mode to the
pilot to avoid confusion. Additionally, if selection between HPa and inches Hg in the Kollsman Window is
selectable, the selected mode must be clear and easily interpreted by the pilot.
Page MG 19 - 19
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.