Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
(i) Ground Station. The ground station must have equipment and
instrumentation to determine wind direction and velocity, outside air temperature, and if
the test rotorcraft has reciprocating engines, humidity. Since the tests must be
conducted in winds of 2 knots or less, a smoke generator is highly recommended to
show both flightcrew and ground crew personnel the wind direction and velocity at any
given time. Additionally, the location of the ground station should be such that it is free
of rotor downwash at all times. Motion picture or phototheodolite and radio equipment
will be necessary to properly conduct the test program. The use of telemetry equipment
is desirable if the location of the test site and the magnitude of the test program make it
practical.
(ii) Airborne Equipment (Test Rotorcraft). Necessary installed test equipment
may include photopanels or recorders for recording engine parameters, control
positions, landing gear loads, landing gear deflections, airspeed, altitude, and other
variables. An external light attached to the rotorcraft (or any other means of identifying
the engine failure point to the ground camera or phototheodolite) is needed to identify
the exact time of engine failure and may also be used to synchronize the ground
recorder with the airborne recorded data.
(2) Analytical Prediction. The HV diagram can be estimated by analytical means
and this is recommended prior to test. HV, however, is the least predictable of all
rotorcraft performance and because of this, the expansion and extrapolation of test data
must be done with great care. Test weight may not be extrapolated. All test points
should be approached conservatively with some speed or altitude margin. If the
applicant has conducted a comprehensive HV flight test program to validate his
analytical predictions, much preliminary testing can be eliminated. In any case, the
maximum allowable extrapolation from flight test conditions is 2,000 feet density
altitude, and an approved analytical or simulation method must be utilized for
extrapolation.
(3) Power.
(i) The appropriate power level before engine failure for the low and high hover
points is simply the power required to hover at the prevailing hover conditions. The
appropriate power condition prior to failure of the engine for points below the knee is
takeoff power or a lower value if approved as an operating procedure. For cruise or “fly
in” points above the knee, the appropriate condition is power required for level flight.
(ii) The applicable power failure conditions are listed in § 29.79(b). Power
should be completely cut for normal category rotorcraft. For multiengine rotorcraft that
comply with the category A engine isolation design requirements, the HV envelope may
be determined with OEI and the desired topping power (for the remaining engine(s))
should be set prior to the test. This power value will need adjustment as ambient
conditions change. The power can be takeoff power (TOP), 2 ½-minute power, or some
calculated lower power for simulating hot day or higher density altitude conditions.
Power is verified and recorded by the pilot by “topping” the engine(s) prior to engine
Page B - 39
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.