Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
failure tests. Care must be taken to ensure that this power value is no more than that
which would be delivered by a minimum specification engine under the ambient
conditions to be approved.
(4) Test Loadings. Weight extrapolation is not permitted for HV. Therefore, the
test weight must be closely controlled. Ballast or fuel should be added frequently to
maintain the weight within -1 to +5 percent when testing final points. Ordinarily, tests
are conducted at a mid-center of gravity unless a particular loading is expected to be
particularly critical.
(5) Landing Gear Loads.
(i) Instrumented landing gear can be a great help in evaluating test results. This
information can be telemetered to a ground station or otherwise recorded and displayed
for direct reference following each landing.
(ii) Any landing which results in permanent deformation of aircraft structure or
landing gear beyond allowable maintenance limits is considered an unsatisfactory test
point.
(6) Piloting Considerations. In verifying the HV diagram, the minimum certificated
instrument panel display and minimum crew should be used in order not to mislead the
operational pilot who has no test equipment available and may have no copilot to assist.
Three distinctly different flight profiles are utilized in developing the diagram.
(i) High Hover. A stabilized OGE hover condition prior to power failure is
essential. A minimum 1-second time delay between power failure and initial control
actuation is utilized. Following the time delay, the primary concern is to quickly lower
collective and to gain sufficient airspeed to allow an effective flare approaching
touchdown. While the immediate development of airspeed is necessary, the dive angle
must be reasonable and must be representative of that expected in service. While initial
aircraft attitude will vary between models and with changing conditions, 10°-20° has
been previously applied as a maximum allowable nose down pitch attitude. Use of
greater attitudes could result in a diagram which is difficult to achieve and unrealistic for
operations in service. Initial testing should start relatively high with gradual lowering of
height to the final high hover altitude. A stabilized OGE hover condition prior to power
failure is essential. If a stabilized high hover condition cannot be achieved prior to the
engine cut, then this point should be tested from a minimum level flight speed. This will
result in an open-ended HV diagram. A smoke source or balloon on a long cord is
highly desirable since the wind can vary significantly from surface observations to
typical high hover altitudes. Vertical speed must be very near zero at the throttle chop.
Any climb or sink rate can have a significant influence on the success of the test point.
Use of a radar altimeter with a cross check to barometric altitude is essential.
Page B - 40
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.