Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
are approached from above and below respectively. Portions near the knee are initially
evaluated at high speed with subsequent backing down of the speed. In most rotorcraft
the effective flare airspeed is critical. At airspeeds slightly below this value, the ability to
arrest and control descent rates through use of an aft cyclic flare may be greatly
diminished. Extreme care should be exercised when “backing down” to lower speeds.
(6) In addition to the on-board and ground instrumentation, a motion picture
camera or other position measuring equipment should cover each run.
(7) For FAA/AUTHORITY tests, the minimum required crew and the minimum
instrument panel display presented for certification should be used. Ground safety
equipment should be provided.
(8) This test is the least predictable of all the performance items. Therefore, the
expansion and extrapolation of test data are questionable. Weight may not be
extrapolated to higher values. In order to extrapolate HV data to higher altitudes, any
analytical method must have FAA/AUTHORITY approval. In lieu of pure analytical
methods, simulations have been used successfully, especially for multiengine rotorcraft.
In either case, the maximum allowable extrapolation should be limited to 2,000 feet
density altitude (HD). HV test weights for normal category rotorcraft are the maximum
weight at sea level and some lesser weight at high density altitudes. The high density
altitude HV curve needs to be defined only to 7,000 feet and may be a lower altitude if
the rotorcraft does not have the performance capabilities to attain 7,000 feet. A weight
less than the maximum weight may be used to define the high density altitude HV
curve, but this weight should not be less than the maximum weight that will allow
hovering out of ground effect (OGE). For a given diagram, typical weight reductions
that are necessary as altitude is increased can be conservatively estimated by
maintaining a constant gross weight divided by density ratio, GW/σ (see Figure
AC 27.79-2, Part A). If weight is not varied, an enlarged HV diagram is required for safe
power-off landing as density altitude is increased (see Figure AC 27.79-2, Part B).
Another method of presentation is to show varying weights at a constant density altitude
(see Figure AC 27.79-2, Part C.)
(9) The FAA accepts, as a method of extrapolation, a weight penalty of 3% for
each 1000 feet above the permitted 2000 feet extrapolation. This weight penalty has
been applied to extrapolations along a constant gross weight divided by density ratio,
GW/σ.
(10) Vertical takeoff and landing (VTOL) testing normally does not require
separate HV testing. The takeoff and landing tests take on the combined characteristics
of takeoff, landing, and HV tests.
b. Procedures.
(1) Instrumentation.
Page B - 38
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.