Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
AC 27.79. § 27.79 LIMITING HEIGHT-SPEED ENVELOPE.
All of the policy material pertaining to this AC section remains in effect through
Amendment 27-43. See § 27.87 and this AC’s section 27.87 effective with Amendment
27-44.
a. Explanation.
(1) The height-speed envelope is normally referred to as the height-velocity (HV)
diagram. It defines an envelope of airspeed and height above the ground from which a
safe power-off or one engine inoperative (OEI) landing cannot be made. The diagram
normally consists of three portions: (a) the level flight (cruise) portion, (b) the takeoff
portion, and (c) the high speed portion (see Figure AC 27.79-1). The high speed portion
is omitted on occasions when it can be shown that the rotorcraft can suffer an engine
failure at low altitude and high speed (up to VH) and make a successful landing or climb
out on the remaining engine(s).
(2) Power failure, engine failure, throttle chop, or other similar terms used in this
discussion mean a simulated engine failure. The actual shutdown of an engine to
simulate an engine failure should not be necessary if the simulated procedure ensures
that the engine power is suddenly removed from driving the rotor and remains so. The
normal fuel control deceleration schedule is usually satisfactory for the power removal
for turbine engines but the flight or ground idle speed may have to be set lower than
normal for HV testing.
(3) The avoid areas of the HV diagram are separated by the takeoff corridor. This
corridor should be wide enough to consistently permit a takeoff flight path clear of the
HV diagram using normal pilot skill. The takeoff corridor should always permit a
minimum of ±5 knots clearance from critical portions of the diagram.
(4) The knee of the curve separates the takeoff portion from the cruise portion and
is defined as the highest speed point on the low speed portion of the HV envelope.
Altitudes above this point are considered cruise, or “fly-in,” points, and these test points
require a minimum time delay of 1 second between throttle chop and control actuation
(reference § 27.143(d)). Altitudes below the knee represent takeoff profile points. For
test points in the takeoff portion, use takeoff power (or a lower power selected by the
applicant as an operating procedure) and normal pilot reaction time for corrective
control actuation.
(5) Since the HV diagram may represent the limiting capabilities of the rotorcraft,
each test point should be approached with caution. The manufacturer’s buildup
program should be reviewed to determine the amount of conservatism in the HV
diagram (if any). It should be remembered that the operational pilot will be operating at
or near the HV diagram without the benefit of a buildup program. Buildup testing is
necessary, and it is most important to vary only one parameter at a time to prevent
surprises. Light weight testing is ordinarily conducted first. High and low hover points
Page B - 37
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.