Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 5 6/13/2014
(1) Test Environment. The environment for bench tests includes:
(i) AdFC system should be realistic to the aircraft environment,
including, but not limited to, the mechanical equipment, wiring, cooling, electrical and
hydraulic power supplies, cockpit controls and displays, trim system, actuation system,
and actuator loads.
(ii) If simulation is used, the model must be validated by a means
acceptable to the FAA.
(2) Test Procedure and Expected Results. The test procedures for bench
tests and rig tests should include open loop and closed-loop tests with simulated
failures. The expected results are:
(i) Verification of failure logic, failure management, and resultant
degraded modes.
(ii) Evaluation of transients during and after failure modes.
Note: Compared to validation of failure management in the simulator, the use of
hardware-in-the-loop simulation provides more realistic results with respect to
signal accuracy and resolution, phase delay, and other hardware or software
related effects.
(D) Rotorcraft Test.
(1) Ground Test. Verification of some aspects of the AdFC functionality
should be possible on the ground, such as determination of stuck or jammed controls or
actuators. Ground testing should be performed to check the safety functions with the
equipment installed in the aircraft. Operation tests should demonstrate that the flight
control system is free from jamming. Limit load static tests should demonstrate
compliance with limit load requirements.
(2) Flight Test. The objective of flight tests is to show compliance with
applicable rules and safety requirements, and to verify assumptions for those objectives
that are not possible during ground testing. Certain effects can only be addressed in
flight, such as aircraft stability and control, aircrew human factors and ergonomics, pilot-
induced oscillations, air resonance, and structural coupling. Rotorcraft performance and
handling qualities under normal and failure operating conditions should be assessed. If
necessary, testing conditions should provide for resetting of failures at any time to return
to the faultless system configuration. Flight tests at various flight conditions with and
without simulated failures should be performed considering event risk assessments and
risk mitigations.
Page MG 17 - 6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.