Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 7 2/4/2016
their heads to bring it into unaided view. Instruments the pilot uses to fly the aircraft should not be placed
on the far side of the instrument panel from the pilot’s seated location.
(iv) Ensure the cockpit can support pilots wearing helmets and NVGs in both the stowed and
operational positions as follows:
(A) Pilots are able to sit in a normal posture in the cockpit and move their head with
NVGs in the operational and stowed positions without hitting cockpit or cabin structures.
(B) Pilots are able to scan across their entire field of regard with NVGs in an operational
position and not hit cockpit or cabin structures.
(C) Previous modifications to the cockpit have not introduced structures that will occlude
the NVG field of view.
(v) Ensure external modifications that can reflect light into the cockpit, such as wire strike kits
or external load mirrors, are modified to support NVG operations. If not, then document those items and
mitigations developed as part of the NVIS lighting modification.
(vi) Perform a failure analysis in accordance with section 27.1309 of this guidance to ensure
the NVIS lighting system design does not introduce hazards to the aircraft.
(A) The failure analysis should identify NVG-compatibility hazards that may occur if the
NVIS lighting (or another aircraft system that can affect NVG compatibility) fails in such a manner as to
introduce incompatible light into the cockpit or into the NVGs’ field of regard. The integrity level of the
system is required to be commensurate with the assessed failure condition classification. The RTCA
Document DO-275 defines the design assurance for NVIS lighting. Complete loss of the NVIS lighting
system is classified as major, and therefore its loss shall be improbable. Inadvertent or uncommanded
actuation of NVG incompatible light sources is classified as severe-major/hazardous, and therefore must
be extremely remote. Design consideration should take into account that component failures and system
design be failsafe. For instance, any incompatible lighting switch should include design features that
prevent inadvertent activation, such as a lever lock or guarded switch. In addition, for designs that install
a stand-alone alternate lighting system instead of altering the aircraft’s original lighting system, the hazard
classification for the failure of the stand-alone alternate lighting system should be the same as that for a
lighting system on a VFR aircraft.
(B) One successful method used a single lighting system with NVIS white compatible
lighting as the interior lighting source for both the cockpit and passenger cabin, which is useable for both
unaided and aided flight. NVIS lighting that incorporates both conventional (non-NVIS) and NVIS lighting
sources requires an SSA to identify the hazards of inadvertent or un-commanded change to non-NVIS
lighting in both the cockpit and cabin. The NVIS lighting system must support transition from aided to
unaided flight in the event of total loss of NVG view.
(5) Mechanical installation. The designer should observe good engineering practices in
specifying material type, wire routing, fastener type, light switches and controls, edge distance, and
ergonomic considerations. If the NVIS lighting design involves modification of another manufacturer’s
installed equipment, the designer should adhere to the manufacturer’s recommendations regarding
modification of its equipment.
(6) Required equipment, instrument arrangement and visibility.
(i) In addition to the instruments and equipment required for flight at night, the following
additional instruments and equipment will typically be necessary for NVG operations (to be defined for
each helicopter). Review applicable operational regulations that specify aircraft equipment required for
night and NVG operations.
Page MG 16-6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.