Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(B) Air intake total temperature rise
(C) Exhaust back pressure
(D) Accessory power extraction
(E) Compressor bleed air extraction
(F) Off-optimum power turbine output speed effects
(iii) The above items and methods of dealing with them are clearly defined
in SAE Aerospace Recommended Practice (ARP) 1702. Typically, these losses will not
be a fixed percentage but will vary with engine operating conditions and environment.
(iv) Any calculations involving power assurance data should use the
approved engine performance program, and the rotorcraft losses should be input on a
discrete basis so that the interaction between losses and their independent variability is
properly considered. This approach is clearly defined in ARP 1702. Accurate
consideration of the losses should produce a Power Assurance Check that will preclude
premature removal of acceptable engines or continued operation of inadequate power
plants.
g. Rotorcraft Flight Manual RFM).
(1) The Power Assurance Check data for the installed engine (engine data
adjusted for inlet losses, exhaust losses, bleed extraction, power extraction, and
off-optimum output shaft speed operation) should be presented in the RFM in an easily
useable format. The data format may consist of charts of engine torque (at constant
power turbine shaft speed) versus allowable values of gas generator speed and gas
path temperature covering the range of ambient conditions for takeoff operations.
Associated limitations for the rotorcraft transmission and the engine should be noted.
(2) The RFM should also:
(i) Include succinct statements of the reason for the Power Assurance
Check and what must be done if the Power Assurance Check results are not
acceptable.
(ii) Clearly state that Power Assurance Check either is a pre-takeoff or
in-flight procedure, as required by operations, specifications and/or other approval
authority documents.
(iii) Be kept simple, easy to use, and identify equipment operation
limitations and requirements.
Page MG 9 - 7
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.