FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 870

PDF page 870 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 870
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                       3/31/2014


program should also be established, reviewed, and approved early to ensure proper
substantiation.

         (5) The fifth area is the static strength evaluation requirements of §§ 27.305
and 27.307 for composite structure. Structural static strength substantiation of a
composite design should consider all critical load cases and associated failure modes,
including effects of environment, material and process variability, and defects or service
damage that are not detectable or allowed by the quality control, manufacturing
acceptance criteria, or maintenance documents of the end product. The static strength
demonstration should include a program of component ultimate load tests, unless
experience exists to demonstrate the adequacy of the analysis, supported by
subcomponent tests or component tests to accepted lower load levels. The necessary
experience to validate an analysis should include previous component ultimate load
tests with similar designs, material systems, and load cases.

                  (i)   The effects of repeated loading and environmental exposure, both of
which may result in material property degradation, should be addressed in the static
strength evaluation. This can be shown by analysis supported by test evidence, by
tests at the coupon, element or subcomponent levels, or alternatively by existing data.
Earlier discussions in this AC address the effects of environment on material properties
(reference paragraph g(2) of this AC paragraph) and protection of structure (reference
paragraph g(3) of this AC parapraph). Static strength tests should be conducted for
substantiation of new structure. For the critical loading conditions, two approaches to
account for prior repeated loading and environmental exposure for structural
substantiation exist.

   • In the first approach, the large-scale static test should be conducted on structure
       with prior repeated loading and conditioned to simulate the environmental
      exposure and then tested in that environment.

   • The second approach relies upon coupon, element, and sub-component test data
       to assess the possible degradation of static strength after application of repeated
      loading and environmental exposure. The degradation characterized by these
       tests should then be accounted for in the static strength demonstration test (e.g.,
      load enhancement), or in the analysis of these results (e.g., showing a positive
      margin of safety with allowables that include the degrading effects of
      environment and repeated load).

In practice, the two approaches may be combined to get the desired result (e.g., a
large-scale static test may be performed at temperature with a load enhancement factor
to account for moisture absorbed over the aircraft structure’s life).

                   (ii)   The strength of the composite structure should be statistically
established, incrementally, through a program of analysis and tests at the coupon,
element, subcomponent, or component levels. As part of the evaluation, building block
tests and analyses at the coupon, element, or subcomponent levels can be used to


Page MG 8 - 14

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →