FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 811

PDF page 811 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 811
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

                        CHAPTER 3
                  AIRWORTHINESS STANDARDS
               NORMAL CATEGORY ROTORCRAFT

                 MISCELLANEOUS GUIDANCE (MG)

AC 27 MG 4. FULL AUTHORITY DIGITAL ELECTRONIC CONTROLS (FADEC)

     a. FULL AUTHORITY DIGITAL ELECTRONIC CONTROLS (FADEC) FOR
INSTALLATIONS WITH CATEGORY A ENGINE ISOLATION.

         (1) Background. The advent of “microprocessor technology” has resulted in
rotorcraft engine controls being implemented by digital process control rather than by
conventional means. These digital, processor-based full authority engine controls offer
many performance advantages (such as isochronous governing) which were not
feasible with conventional technology, pneumatic or hydromechanical controls.
Because of the incorporation of this advanced technology, some additional
considerations must be made of the engine installation to ensure regulatory compliance.

                  (i)    Part 27 does not require engine isolation. The guidance herein does
not address FADEC installation certifications which do not desire engine isolation credit.

                   (ii)    In showing compliance with certain performance and flight
characteristic sections of Part 27, simultaneous malfunction of engines is not
considered if Part 29 Category A engine isolation is achieved. Paragraph AC 27.MG 3
describes, in terms of Part 29 Category A requirements, an acceptable approach for
determining that engine isolation, adequate for Part 27 performance and flight
characteristic credit, has been achieved. That guidance material should be reviewed,
but it is not believed that the limited-time-period concept for engine isolation which could
be allowed under Part 27 would affect the FADEC installation requirements. Hence, the
guidance for a Part 27 aircraft claiming credit for engine isolation is essentially the same
as for a Part 29 Category A rotorcraft.

         (2) Procedures. The following is a discussion of some special attention areas
when a FADEC installation is to be shown to comply with the Part 29 Category A engine
isolation requirements. Paragraph AC 27.1309b(4)(i)(D) of this AC contains a general
definition of what constitutes a “full authority” control.

                  (i)   Software Qualifications.

              (A) Paragraph AC 27.1309f contains a general discussion on the use of
the RTCA/DO-178B document that is used for the approval of system software.
FADECs are generally developed to Level A software under RTCA Document DO-178B
based on the hazard category of the FADEC failure condition(s). However, if an
applicant proposes a FADEC with Level B software based on the Functional Hazard



                                                        Page MG 4 - 1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →