FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-25

PDF page 81 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 81
AC 27-1B · B-25Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                            AC 27-1B


AC 27.51. § 27.51 TAKEOFF.

   a. Explanation. Section 27.51 details the conditions under which takeoff data must
be obtained. The flight manual must contain the technique(s) to be used to obtain the
published flight manual takeoff procedures. Technique should not be confused with
exceptional pilot skill and/or alertness as mentioned in § 27.51. Because rotorcraft
differ, different pilot techniques are sometimes required to achieve the safest and most
optimum takeoff performance. The recommended technique that is published in the
flight manual must be determined to be one that the operational pilot can duplicate
using the minimum amount of type design cockpit instrumentation and the minimum
crew. Only rotorcraft takeoff techniques will be covered in this section.

   b. Background.

      (1)   Certain special takeoff techniques are necessary when a rotorcraft is unable
to take off vertically because of altitude, weight, power effects, or operational limitations.
The recommended technique used to take off under such conditions is to accelerate the
rotorcraft in-ground-effect (IGE) to a predetermined airspeed prior to climbout. Takeoff
tests are performed to determine the best repeatable technique(s) for a particular
rotorcraft over the range of weight and altitude for which certification is requested.

      (2)   Utilizing the total power available to execute a takeoff may not be
operationally feasible due to such items as HV or aircraft attitude constraints. In such
situations, hover power required plus some power increment may be the maximum
recommended for use.

      (3)  Wheel or skid height should be not less than that demonstrated satisfactorily
for the high speed, low altitude portion of the HV curve, or that height below which
ground contact may occur when accomplishing takeoff procedures.

      (4)  For rotorcraft fitted with wheels, a running takeoff procedure may be
accepted.

   c. Procedures.

      (1)  There are different takeoff profiles which may be used to complete a
maximum performance takeoff in a rotorcraft. The manufacturer will normally determine
which method is best for a particular rotorcraft. The most commonly accepted method
is the hover and level acceleration technique. In this technique, the rotorcraft is
stabilized in a hover at the reference height. From the stabilized hover, the rotorcraft is
accelerated to the climbout airspeed using the predetermined takeoff power. When the
desired climbout airspeed is achieved, the rotorcraft is rotated and the climbout is
accomplished at the scheduled airspeed(s) and constant rotor RPM. Power
adjustments may be accomplished to maintain the targeted power except where
procedure requires high workload outside the cockpit (i.e., that portion of takeoff where



                                                        Page B -25

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →