Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 9/17/2009
As a technique, it is recommended the rotorcraft be loaded to a center of gravity (CG)
near the hook to minimize fuselage angle changes with varying powers. All tethered
hover data should be verified by a limited spot-check using the free flight technique.
The free flight technique in AC 27.49.b.(4) will determine if any problems, such as load
cell malfunctions, have occurred. The free flight hover data must fall within the
allowable scatter of the tethered data.
(4) If there are no provisions or equipment to conduct tethered hover tests, the free
flight technique is also a valid method. The disadvantage of this technique, as the
primary source of data acquisition, is that it is very time consuming. In addition, a
certain element of safety is lost OGE in the event of an emergency. The rotorcraft must
be re-ballasted to different weights to allow the maximum Ct/Cp spread. When using the
free flight technique, either as a primary data source or to substantiate the tethered
technique, the same considerations for wind, recorded parameters, etc., as used in the
tethered technique, apply. Free flight hover tests should be conducted at CG extremes
to verify any CG effects. Applicants must account for any rotorcraft stability
augmentation system that may influence hover performance.
(5) Comprehensive hover performance tests are typically conducted at low,
intermediate (~7000 feet Hd), and high altitude test sites, with prepared landing
surfaces, in conjunction with takeoff, landing, controllability, and maneuverability
testing. Alternatively, a predicted hover performance model developed for high altitude
may be used if verified by limited flight-testing. The extrapolation guidelines in AC
27.45.b.(2) are still applicable. These higher altitude hover tests could typically be
conducted in conjunction with the limited controllability tests. If the applicant is able to
demonstrate to the FAA/AUTHORITY a method to provide a reliable hover reference, it
is acceptable to conduct OGE tests without ground reference. Hover performance can
usually be extrapolated up to a maximum of 4,000 feet above the highest test site
altitude.
Page B - 24 4
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.