Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(7) Environmental Qualification. Each component of the system, such as
relays, switches, alternator, generator, sensor, regulator, diode, etc., should be qualified
to the critical environmental parameters. The temperature, altitude, humidity, and
vibration expected in the approved aircraft operational envelope should fall within those
limits the applicant substantiates for the electrical system components. (Refer to
paragraph AC 27.1309.)
(8) Electromagnetic Compatibility. At no time during any of the qualification
testing described herein should objectionable interference in the aircraft’s radio,
navigation, cockpit instrument, autopilot, or interphone system be considered
acceptable.
NOTE: The quantitative type testing used for paragraphs b(7) and (8) above is outside
the scope of this document. The latest revision of RTCA Document DO-160 is an
acceptable standard.
(9) Transient Tests. The dc system should be tested and shown to exhibit
surge, ripple, and spike voltages within the limits of the latest revision of
RTCA Document DO-160.
(i) The surge and ripple voltage tolerance of avionic equipment is defined
by section 16 of the latest revision of RTCA Document DO-160. Category Z is
considered applicable to rotorcraft dc systems.
(ii) The voltage spike tolerance of avionic equipment is defined by
section 17 of the latest revision of RTCA Document DO-160.
(10) Ground and Bench Test Report. At the conclusion of the ground and
bench test program, a report should be prepared and submitted that contains at least
the following:
(i) System schematic (including instrumentation tie-in).
(ii) Instrumentation list (including calibration records).
(iii) Test result recordings.
(iv) Detailed procedures and results obtained.
(v) Conformity inspection records.
(vi) Other data, photographs, etc., to describe the test setup.
(vii) Summary of the test results. This summary should show the
maximum load to which each bus, alternator/generator, etc., has been tested.
Page MG 2 - 5
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.