Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
NOTE: All of these tests are to be conducted with the battery OFF since the purpose of
the tests is to determine if the ship’s battery is necessary for excitation of the
alternator(s)/generator(s).
(i) Minimum anticipated electrical load, low engine RPM, and
alternator(s)/generator(s) OFF. Demonstrate that when an alternator/generator is
turned ON, it will come on the line. Repeat for any other alternators/generators in the
system.
(ii) Maximum electrical load, low engine RPM, and
alternator(s)/generator(s) OFF. Demonstrate that each alternator/generator will
individually come on the line.
(iii) Minimum anticipated electrical load, high engine RPM, and
alternator(s)/generator(s) OFF. Demonstrate that each alternator/generator will
individually come on the line.
(4) Stabilization.
NOTE: All of these tests are to be conducted with the ship’s battery OFF, since the
purpose of the tests is to determine if the ship’s battery is necessary for stabilization of
the alternator/generator. In each case, if the ship’s battery is not necessary for
stabilization, the alternator/generator should be on the line and remain there at a
satisfactory voltage level.
(i) Minimum anticipated electrical load, low engine RPM,
alternator(s)/generator(s) ON. Switch on the heaviest electrical load that is anticipated
to be installed on the aircraft.
(ii) Repeat b(4)(i) for a maximum electrical load and low engine RPM.
(iii) Repeat b(4)(i) for a minimum anticipated electrical load and high
engine RPM.
(iv) Repeat b(4)(i) for a maximum electrical load and high engine RPM.
(5) System Malfunctions.
(i) System malfunction testing should be conducted as necessary to
verify a fault analysis of the proposed electrical system. Depending on the complexity
of the proposed system and the comprehensive nature of the system fault analysis,
these tests may be necessary. Analysis/testing is typically only required for IFR and
CAT A complex electrical systems, not basic Part 27 systems. This satisfies the need
to verify all analysis, and complex designs are usually verified by tests. IFR and CAT A
electrical systems are complex in nature and tests are required to verify the analysis.
Page MG 2 - 3
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.