Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
CHAPTER 3
AIRWORTHINESS STANDARDS
NORMAL CATEGORY ROTORCRAFT
MISCELLANEOUS GUIDANCE (MG)
AC 27 MG 2. STANDARDIZED TEST PROCEDURE FOR ROTORCRAFT DC
ELECTRICAL SYSTEM TESTS.
a. Test Requirements.
(1) General. The following functions and characteristics are to be evaluated:
(i) Normal System Operation.
(ii) Parallel Load Division.
(iii) Excitation.
(iv) Stabilization.
(v) Systems Malfunction.
(vi) Environmental Capability.
(vii) Electromagnetic Compatibility.
(viii) Cooling Capability.
(ix) Surge Characteristics, Ripple Voltage, and Voltage Spikes.
(2) Instrumentation. Calibration records should be available for all
instrumentation. Enough specific currents and voltages should be recorded to allow
reconstruction of any sequence of events that would happen as a result of any system
testing described herein.
(3) Regulatory References. Sections 27.1301, 27.1307(c), (d), (e), 27.1309,
27.1351, 27.1353, 27.1357, 27.1361, 27.1365, and 27.1367.
(4) Miscellaneous, The assigned FAA/AUTHORITY systems and equipment
engineer normally witnesses these tests and should be notified as far in advance of the
testing as possible to minimize scheduling problems. Conformity of the test setup must
be established prior to conducting any testing. Most of the above test categories can be
conducted on a bench test setup. A bench test setup is especially recommended in the
case of the system malfunction test. It is the applicant’s option to demonstrate his
equipment either on the bench or installed for ground tests. When a bench setup is
Page MG 2 - 1
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.