Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
AC 27.1589. § 27.1589 LOADING INFORMATION.
a. Explanation. Control of the rotorcraft weight and balance is an operational
function and is the responsibility of the operator. However, instructions necessary to
enable loading of the rotorcraft within the established limits of weight and center of
gravity and to maintain the loading within such limits are required by the operating
regulations, and inclusion of such loading instructions in the Rotorcraft Flight Manual is
required by this rule. Approved loading instructions, therefore, must be presented in the
Rotorcraft Flight Manual and, at the option of the applicant, may be included in the
approved portion or in the unapproved portion.
b. Procedures.
(1) For the purpose of the flight manual, distinction is made here between the
loading instructions required by the certification requirements of Part 27 and the weight
and balance data required by the operating requirements. The former prescribed
information is applicable to the rotorcraft type and is subject to FAA/AUTHORITY
approval as flight manual material.
(2) For compliance with the noted requirements, it is necessary for the
applicant to develop weight and balance data and loading instructions as necessary to
satisfy the needs of both certification and operation. In order to consolidate in one
document information on rotorcraft loading, it is recommended that the weight and
balance data be developed to include appropriate loading instructions, and that both be
included in the Rotorcraft Flight Manual as an “unapproved” section entitled “Weight and
Balance.” Such a section should include the following statement as a note: “In
accordance with FAA/AUTHORITY procedures, the detail weight and balance data of
this section are not subject to FAA/AUTHORITY approval. The loading instructions of
this section, however, have been approved by FAA/AUTHORITY as satisfying all
requirements for instructions on loading of the rotorcraft within approved limits of weight
and center of gravity and on maintaining the loading within such limits.”
(3) For initial approval of the manual, an actual or specimen weight and
balance section should be submitted for evaluation and approval of the loading
instructions. Weight and balance data for each particular rotorcraft need not be
submitted for approval as flight manual material unless a substantive change is made to
the approved loading instructions.
(4) The weight and balance material outlined below is believed to be adequate
for rotorcraft with conventional loading and fuel-management techniques. For rotorcraft
which necessitate redistribution of fuel (other than normal consumption) to maintain
loading within prescribed limits, the material should be amplified as necessary.
(i) Weight Limits. A list and explanation, where necessary, of all
fixed-weight limitations should be included.
Page G – 48.1
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.