FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page G-27

PDF page 752 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 752
AC 27-1B · G-27Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4

AC 27.1555. § 27.1555 (Amendment 27-21) CONTROL MARKINGS.

     a. Explanation. Section 27.1301(b) requires that all installed equipment be
labeled to identify its function and operations; however, this section provides more
detailed requirements for control markings. Specific criteria are given for powerplant
fuel controls, fuel quantity markings, and landing gear controls. The requirement to
color emergency controls red is in this section.

     b. Procedures.

         (1) Section 27.1555(a) requires each cockpit control, other than flight controls
whose function is not obvious, to be appropriately labeled. The primary flight controls
are the cyclic, collective, and the directional control (tail rotor) pedals. For the control to
be appropriately labeled, the rule requires that there should be an obvious and clear
demarcation of the function and operation of the control. When performing the
evaluation to determine the adequacy of markings, remember that only those controls
which are quite traditional should be judged to be obvious in their operation. An
example of this has been the navigation/communication (NAV/COMM) control heads.
The more traditional control units had concentric knobs of decreasing size for the
selection of frequency. Because this system was so common for such a period of time,
the finding was generally made that the function of this control was obvious and thus did
not require a specific marking. However, as more current technology digital electronic
controls were used, the frequency selectors were judged not to be obvious in their
operation, and their function and operation were required to be labeled.

         (2) Review design data and available hardware to ensure the powerplant fuel
controls are clearly and permanently marked such that:

                  (i)    Selector valve control clearly shows each position for each tank and
each crossfeed configuration.

                   (ii)   Tank selection sequences required for safe operation are clearly and
permanently marked on or adjacent to the required selector.

                    (iii)  Each control valve is clearly marked to show the position of the
controls for each engine on multiengine rotorcraft.

         (3) Review design data and available hardware to ensure that usable fuel
capacity is clearly marked as follows:

                  (i)      If the fuel system has no selector controls, usable fuel capacity must
be shown on the fuel quantity indicator (reference paragraph AC 27.1553).

                   (ii)     If the system has selector controls, the usable fuel capacity at each
selector position must be clearly shown near the selector position.



                                                       Page G - 27

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →