Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/2008 AC 27-1B, Chg 3
SUBPART F - EQUIPMENT
ELECTRICAL SYSTEMS AND EQUIPMENT
AC 27.1351. § 27.1351 (Amendment 27-13) ELECTRICAL SYSTEMS AND
EQUIPMENT--GENERAL.
a. Explanation. With the advent of more sophisticated rotorcraft and operations
under more critical conditions, such as IFR and icing, it is essential that the electrical
system be very carefully analyzed and evaluated to assure proper operation under any
foreseeable operating condition and that hazards do not result from any malfunctions or
failures.
b. Procedures.
(1) Electrical System Capacity. Rotorcraft electrical systems have grown in
capacity, complexity, and impact on safety. This paragraph requires adequate electrical
system capacity for safe operation of load circuits essential for safe operation at
continuous rated power. If this capacity can be shown by electrical measurements, an
electrical load analysis is not required. However, if the measurement method of
compliance is chosen, data should be provided to show that the measured loads
represent the worst case electrical loading for components or combination of
components.
(i) Load circuits (systems) that are essential for safe operation are those
systems necessary to maintain controlled flight and land safely and are generally those
systems required to show compliance with the certification regulations. This includes
most electrical utilization systems.
(ii) An electrical utilization system is a system of electrical equipment,
devices, and connected wiring using electric energy to perform a specific aircraft
function.
(iii) The specific utilization systems, which are necessary to maintain
controlled flight and land safely, will vary with the type of rotorcraft and with the nature
of operations. Examples of systems which may be essential are basic flight
instruments, minimum navigation equipment, minimum radio communications, and flight
control systems.
(2) Function.
(i) Generating systems should be analyzed, inspected, or tested to
ensure that no probable malfunction in the generating system or in the generator drive
system may cause loss of service to systems essential for safe operation. A probable
malfunction is any single electrical or mechanical component malfunction or failure that
Page F - 55
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.