Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
in excess of 6 percent of the gauge reading, corrective information should be applied
adjacent to the fuel quantity gauge or be made available to the crew in other handbook
data.
(ii) Flight during hover with maximum rearward wind may introduce
significantly different fuel gauge readings. A check should be made to ensure that the
gauge is either accurate or at least does not read high (unconservative) in this attitude.
(iii) If external loads are approved, the attitude for this type of operation
should be considered.
(iv) Consistent with the requirements of § 27.1337(b)(2), a separate fuel
quantity indication is necessary for any interconnected fuel tank that has a flow control
device, such as a fuel transfer pump or flapper valve, which could fail and trap fuel.
This requirement also applies to auxiliary fuel tanks. A sight gauge that is readable by
the flight crew in flight may be acceptable for use with auxiliary fuel tanks.
(4) Fuel gauging system transmitters which are strictly volumetric measuring
devices (float-actuated variable rheostats) introduce a gauge readout error of about
5 percent if calibrated with a fuel temperature of 0°C (32°F) and subjected to -55°C
(-67°F) fuel or +55°C (131°F) fuel. This error may be minimized by calibrating the
gauge with fuel temperature in the middle of the useful range (i.e., 15°C (59°F)). These
types of gauging systems should be recalibrated during periodic major maintenance
intervals. The manufacturer should be urged to include procedures and requirements
for this in the “Instructions for Continued Airworthiness” for the model rotorcraft.
(5) Capacitance transmitters have become the standard for most modern fuel
systems. These transmitters ordinarily need no temperature compensation since the
fuel volume and the fuel dielectric constant vary inversely as temperature changes. The
basic capacitance transmitter does not compensate for the different dielectric values to
be expected with different type fuels. An add-on capacitance located where it will be
submerged in fuel at all times can be devised to automatically compensate for other
fuels.
AC 27.1337A. § 27.1337 (Amendment 27-23) POWERPLANT INSTRUMENTS.
a. Explanation. Amendment 27-23 adds § 27.1337(e) that requires certain rotor
drive system transmissions and gearboxes to be equipped with chip detector systems.
These detectors will sense and signal the presence of ferromagnetic particles to the
flight crew. This amendment will improve the level of safety available with the
installation of chip detector systems.
b. Procedures. All of the policy material pertaining to this section remains in
effect. Additionally, the following information is added about chip detectors. The chip
detectors should:
Page F – 54.3
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.