Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
AC 27.1337. § 27.1337 (Amendment 27-12) POWERPLANT INSTRUMENTS
(Paragraph (b) - FUEL QUANTITY INDICATOR).
a. Explanation. Section 27.1337(b) requires, in part, a means to indicate to the
flight crew the quantity of usable fuel during flight in each tank. When two or more tanks
are interconnected so that a failure of the system could cause fuel to become trapped in
a fuel tank, the fuel quantity indicating system must provide the flight crew with the
ability to determine the total effective amount of remaining usable fuel. Since the flight
attitude of a rotorcraft may vary significantly with center of gravity (CG) and airspeed,
several attitudes for calibration of the fuel gauge may be appropriate. Accordingly, the
manufacturer should review the operational envelope (with respect to attitudes) and
select at least three attitudes for gauge calibration with the provision that these attitudes
should be useful to the intended operation of the rotorcraft and demonstrate gauge
accuracy (within limits suggested herein). Selection of ground attitude for one of these
conditions may, in some cases, be appropriate.
b. Procedures.
(1) Determine the rotorcraft pitch attitudes for most forward and most aft CG at
a median gross weight and at an airspeed of 0.9 VNE or 0.9 VH, whichever is less. The
mean attitude of the extremes defined above, further adjusted for lateral CG effects, if
necessary, define the rotorcraft attitude for fuel gauge calibration.
(2) After establishing the calibration attitude, the requirements of § 27.1337(b)
can be accomplished. The aircraft should be placed in the calibration attitude. Add fuel
to the filler neck spillover level. Defuel the aircraft in increments corresponding to fuel
gauge increment markings or at least 10 increments until gauge zero is obtained.
Precautions should be taken during this step to be sure that the fuel transmitter is
sensing fuel level and not simply reflecting a physical “STOP” or end point in the system
range. The fuel remaining in the tank below the “ZERO” mark must not be less than
that amount determined by flight testing under § 27. 959. (Otherwise, the zero point
must be adjusted upward.) The gauging system accuracy is acceptable when it meets
a tolerance of ±2 percent of the total useable fuel plus ±4 percent of the remaining
usable fuel at any gauge reading, provided that the gauge indicates zero fuel with
unusable fuel in accordance with § 27.959 in the tank. (For a 100-gallon tank, this
formula would allow a ±6-gallon error at the full level, ±4-gallon error at 50-gallon level,
converging to a ±2-gallon error at low fuel with the further provision that the zero mark
accurately reflects unusable fuel.)
(3) Certain other aspects of a fuel gauging system need attention in order to
minimize fuel exhaustion incidents:
(i) Gauge reading with the aircraft at ground attitude is frequently used by
the crew in calculating range, weight and balance, and actual gross weight. Significant
gauge errors in either direction during this reading can introduce hazards to the
operation of the aircraft. If a calibration at this attitude indicates an unconservative error
Page F – 54.2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.