Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
6/23/23 AC 27-1B, Chg 9
limitations section of the instructions for continued airworthiness in the maintenance
manual, as required by § 27.1529 and Appendix A to Part 27.
Note: CMRs may be needed to help show compliance with § 27.1309 for significant
latent failures. Rational methods, which usually involve quantitative analyses or
relevant service experience data, should be used to determine CMR intervals. It is
recognized that, for various reasons, component failure rate data is not precise
enough to accurately estimate the probabilities of Failure Conditions. This results in
some degree of uncertainty, as indicated by the expression “on the order of” in the
definition of the quantitative probability terms in paragraph c(1) above. These intervals
should have reasonable tolerances so that CMRs can be performed concurrently with
other maintenance, inspection, or check procedures not required by design for
compliance with § 27.1309. Any tolerance ability should be built into the interval that is
included in the airworthiness limitation section of the maintenance manual.
If CMRs are used, they and their intervals and tolerances, and any post-certification
changes or procedures provided in the type design for a rotorcraft owner or operator
to make such changes, must be approved by the FAA office having cognizance over
the type design that relates to the system and its installation, as required by §§ 21.31,
21.95, and 21.97.
(F) When assessing the acceptability of a failure condition using a
quantitative analysis, the given numerical range should normally be interpreted to be
the allowable risk for an hour of flight time based on a flight of mean duration for the
rotorcraft type. However, when assessing a function that is used only at a specific time
during a flight, the probability of the failure condition should be calculated for the
specific period and expressed as the risk for the flight condition, takeoff, landing, etc.,
as appropriate. This is only true for those systems that cannot fail undetected when
they are being used. The probability of failure for those systems should be calculated
from that value based on the extended period of not only the active operation, but also
the exposure time for the latent failure.
Note: If a quantitative analysis is used to help show compliance with the regulations
for equipment or systems that are installed and only required for a specific operating
condition for which the rotorcraft is thereby approved, credit is usually not allowed due
to the fact that the operating condition does not always exist. If an applicant does
request that such credit be allowed, they must obtain the approval of the FAA.
Page F - 30.9
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.