FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-122

PDF page 542 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 542
AC 27-1B · E-122Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

- A locking device preventing the engine starting when the rotor brake control is not
completely released.

AC 27.1163.    § 27.1163 (Amendment 27-23) POWERPLANT ACCESSORIES.

     a. Explanation.

         (1) This section addresses the interface requirements for powerplant
accessories which are mounted on the engine or rotor drive system components.

         (2) Areas which should be addressed include structural loads imposed upon
the engine case and isolation between the accessory and engine oil systems. Electrical
equipment isolation from flammable fluids or vapors should be addressed as well as the
effect of an accessory failure on the continued operation of the engine and drive system
components.

     b. Procedures.

         (1) Accessories installed and certified by the engine manufacturer can be
mounted on the engine without additional justification.

         (2) Any accessory to be mounted on the engine, which was not certificated with
the engine, and does not meet the engine installation design manual requirements
should have a structural analysis showing the mounting of that accessory on the engine
will not induce loads into the engine case which are higher than the original design
loads.

         (3) When the accessory is mounted and operating on the engine, it should not
be possible to contaminate either the engine or accessory oil systems. This
contamination can take the form of debris following a failure, airborne dirt or water, or
any other substance that would impair proper operation of the engine or accessory.
Compliance with these requirements can be accomplished by a combination of test and
analysis. The design interface should be such that when the equipment is operating,
there are no high/low pressure differentials between the components which would
induce fluid transfer between components resulting in a low fluid level in one component
and an overfill condition in the other component. Where this potential exists, an
analysis and/or test should be used to demonstrate compliance.

         (4) Engine mounted accessories which are subject to arcing and sparking, must
be isolated from all flammable fluids or vapors to minimize the probability of fire. This
can be accomplished by isolating the electrical equipment from the flammable fumes or
vapors or by isolating the flammable fumes or vapors from the potential ignition source.
Compliance can be shown by analysis.

         (5) A failure mode and effect analysis should be submitted which shows that a
failure of any engine mounted and driven accessory will not interfere with the continued


Page E - 122

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →