FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 52

PDF page 52 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 52
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     9/17/2009


approval. Section 133.41 is also appropriate for the individual operator to obtain his
operating certificate. The operator may use an FAA/AUTHORITY approved RFM
supplement to prepare his own rotorcraft load combination flight manual required by
§ 133.47.

     b. Procedures.

         (1) It may not be possible to demonstrate quantitatively all the flight
requirements at the minimum weight because of test instrumentation requirements. The
test team must ensure that the rotorcraft complies with the applicable requirements at
the lowest permissible flying weight. This evaluation may be done qualitatively with the
test instrumentation removed and with minimum crewmembers if no critical areas exist
or are anticipated. Additionally, reasonable extrapolation is permitted. However, if
critical areas at minimum flying weights are apparent, extrapolation should not be
permitted.

         (2) Whenever a gross weight increase under § 27.25(c) is requested, a TIA
evaluation is necessary to evaluate the new limitations and ensure that § 133.41 for
typical or representative cargo weights and/or shapes (or density) is satisfactory.  All
possible combinations of weights and shapes are not evaluated. The representative
configurations may be noted in the RFM or RFM Supplement for the operator’s
information. Sections 133.41 and 133.47 must be satisfied by the individual operator for
the particular case at hand. The approved RFM or RFM Supplement should provide the
necessary limitations and any other information about the representative cargo
configurations evaluated. Section 133.41 also permits the operator to obtain approval
of additional and unique cargo configurations provided approved limitations are
observed. Paragraph AC 27.1581 concerns the RFM and its contents.

         (3) See AC 29-2C, Certification of Transport Category Rotorcraft,
paragraph AC 29.571, concerning § 29.571, for fatigue substantiation and external
cargo considerations that apply to § 27.571 as well.

         (4) Refer to AC 133-1A, Rotorcraft External-Load Operations in Accordance
with FAR Part 133, for further information on airworthiness and flight manual policy for
operators.

AC 27.25A.     § 27.25 (Amendment 27-44) WEIGHT LIMITS.

     a. Explanation. Amendment 27-44 adds a requirement to create weight, altitude,
and temperature limitations for those rotorcraft that are not able to meet the basic
requirements of §§ 27.79 or 27.143(c). The § 27.79 height-velocity diagram must be
demonstrated at maximum weight or at the highest weight allowing out-of-ground-effect
(OGE) hover at a density altitude of 7,000 feet. The § 27.143(c) controllability must be
demonstrated at critical weight at 7,000 feet density altitude.  If either or both of these



Page B – 4

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →