Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
AC 27.1093. § 27.1093 (Amendment 27-20) INDUCTION SYSTEM ICING
PROTECTION.
a. Reciprocating Engines.
(1) Explanation.
(i) Atmospheric moisture, even in clean air and temperatures above
freezing, can result in ice accumulations in induction systems to a degree which can
easily cause engine failure.
(A) Impact Ice. This forms as supercooled water droplets impact on
engine induction system components. Particularly heavy accumulations must be
expected where bends or turns in the induction system force changes in the airflow
direction thus centrifuging the droplets out of the air stream where they freeze on impact
with induction system components. A serious form of impact ice is the collection of ice
on fuel metering elements of the carburetor, the alternate (preheat) valve, and any
screens in the system.
(B) Throttle Ice. This type of ice forms at or near the throttle in a partly
closed position [up to 30°F (-1°C)] due to cooling effect resulting from the increase in
kinetic energy (increased velocity) of the air in the restricted flow area.
(C) Refrigeration Ice. This forms as a result of the cooling effect of the
fuel evaporating after the fuel is introduced into the airstream. For some float type
carburetors, it is possible in rare instances to accumulate serious ice during a closed
throttle glide with ambient air temperatures as high as 93°F (+34°C), and relative
humidity of 30 percent. At low cruise power, ice can occur at outside air temperatures
as high as 62°F (+17°C) and relative humidities as low as 60 percent. Most of the heat
necessary to evaporate fuel is supplied from the air as it drops in temperature. Fuel
evaporation ice can affect airflow by blocking the throat of the manifold riser; it can
affect the fuel-air-ratio by interfering with the fuel flow; and it can affect mixture
distribution or quantity of mixture flowing to individual cylinders by upsetting the fuel flow
distribution, or quantity of mixture flowing to individual cylinders by upsetting the fuel
flow distribution at the fuel nozzle or airflow distribution in the manifold throat. This
refrigeration phenomenon is the most serious of all factors causing carburetor ice.
(2) Procedures. Normally, flight tests with carburetor air temperature
instrumentation are required. Unless otherwise justified, conduct all tests at maximum
gross weight, a median center of gravity, in level flight, and at the engine speed which,
considering cooling fan effects, if any, produces the minimum heat to the carburetor
muff or engine component area utilized to provide the carburetor air heat. The optimum
test condition is flight at the altitude at which the measured outside air temperature
(OAT) is 30°F (-1°C) and when a power setting of 75 percent maximum continuous
power can be maintained. If this combination cannot be achieved, satisfactory
Page E - 101
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.