FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-87

PDF page 505 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 505
AC 27-1B · E-87Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (1) The oil tank should be designed and installed to withstand, without failure,
any vibration, inertia, fluid, and structural loads expected in operation.

         (2) For reciprocating engines, the expansion space should not be less than
0.5 gallons or 10 percent of the tank capacity, whichever is greater.

         (3) For turbine engines, the expansion space should not be less than
10 percent of the tank capacity.

         (4) It should not be possible to inadvertently fill the expansion space with the
rotorcraft in the normal ground attitude.

         (5) Adequate venting should be provided.

         (6) Oil overflow from the filler opening into the oil tank compartment should be
prevented.

     b. Procedures.

         (1) The structural analysis of the tank, including the attachments, should ensure
that the tank will not leak under the vibration, inertia, fluid, and structural loads expected
in service.

         (2) The expansion space may be determined by calculating the difference
between the volume up to the vent opening and the volume to the spillover level of the
filler opening. The expansion space volume must not be less than 10 percent of the
volume to the filler spillover level (tank capacity) or not less than 0.5 gallons for
reciprocating engine installations with oil tank capacities of 5 gallons or less.

         (3) To assure adequate venting under all normal flight conditions, the tank
should be vented from the top portion. Traps where condensed water vapor might
freeze and obstruct the vent line should be avoided.  If other components, perhaps an
engine speed reduction gearbox, are vented to the engine oil tank, the oil tank vent line
should be sized to handle this additional requirement as well as the air normally
entrained in the return oilflow from the engine.

         (4) A suitable method to prevent oil spillover from the filler opening from
entering the compartment containing the oil tank would be a scupper with an attached
drain line that discharges clear of the rotorcraft.

AC 27.1015.    § 27.1015 (Amendment 27-9) OIL TANK TESTS.

     a. Explanation. This regulation specifies the requirements which the oil tank tests
should verify. Each oil tank should withstand, without leakage, an internal pressure of
5 PSI. This regulation also specifies that each pressurized oil tank used with a turbine



                                                       Page E - 87

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →