Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
AC 27.953. § 27.953 FUEL SYSTEM INDEPENDENCE.
a. Explanation.
(1) Section 27.953(a) specifies independent fuel feed systems for each engine
of multiengine rotorcraft; however, separate fuel tanks for each engine are not required.
(2) If a single tank is used to feed more than one engine, § 27.953(b) specifies:
(i) That independent fuel tank outlets be provided to each engine, each
having a shutoff valve.
(ii) At least two vents for the tank located to minimize the probability of
both vents becoming obstructed simultaneously.
(iii) Filler caps designed to minimize the probability of incorrect installation
or in-flight loss.
(iv) That fuel supply from each tank outlet to any engine be independent
of fuel supply to other engines.
b. Procedures.
(1) The purpose of § 27.953(a) is to ensure an independent fuel supply system
for each engine on multiengine rotorcraft. Unlike the corresponding regulation for
Category A, Part 29 rotorcraft, separate fuel tanks are not required.
(2) The assessment of an independent fuel supply system for each engine
would begin at the fuel supply pickup point within the tank and continue to the engine
fuel inlet at the engine.
(3) If supply line crossfeed capability is included as a feature, care must be
exercised to ensure that the opening of the crossfeed does not jeopardize the continued
safe operation of more than one engine. For example, if the crossfeed valve is
automatically operated by a low pressure signal in the supply line for one engine, the
possibility that fuel line leakage could cause opening of the crossfeed and jeopardize
the continued safe operation of both engines should be considered. Similarly, opening
the crossfeed valve with a suction lift system should not allow air into the fuel supply line
of any engine.
(4) The independent fuel supply system requirement for each engine is for
normal fuel system operations. Fuel system designs which allow the continued safe
operation of all engines under expected fuel system component failure conditions (for
example, a failed boost pump) by using common fuel flow paths under failure conditions
are not prohibited.
Page E - 56
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.