FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 441

PDF page 441 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 441
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                       AC 27-1B, Chg 4

             (ii) Procedure. The official flight test plan should include requirements to
investigate the engine operating characteristics for stall, surge, flameout, acceleration
and deceleration response, and transient response (within approved limits) throughout
the operating range of the rotorcraft. The results must show that no adverse
characteristics are present, to a hazardous degree, during normal and emergency
operation within the range of operating limitations of the rotorcraft and engine. Test
configurations should encompass the critical engine power settings and design or
rigging tolerances expected to be seen in service. In addition, normal and degraded
engine operating control modes should be evaluated where applicable. Test conditions
should include maximum airspeed-sideslip combinations, power recoveries, hover with
wind from all directions including tailwinds and other maneuvers appropriate to the
certificated operating envelope of the rotorcraft. In addition, recirculation of exhaust
gases during hover or rearward flight can be critical for engine operation and should be
evaluated. Particular attention should be given to flight and operating conditions that
can be judged critical from review of data on engine inlet pressure and temperature
distribution patterns and engine stall margin data if available. High altitude has typically
been critical for these tests unless other critical areas of the flight envelope are
identified. In addition, during rearward flight at high altitude, results may indicate
unacceptable thermal distortions in the inlet due to reingestion.  Stall, surge, or flameout
which may be hazardous (i.e., causes loss of engine function, causes loss of control,
causes severe torsional shock through the rotor drive system, or otherwise damages
the rotorcraft) is unacceptable. The flight test program should include:

           (A) Normal operation (hover, forward stabilized flight, collective inputs,
rearward flight).

               (1) Checks in hover. Hover with wind from all azimuths to the allowable
wind limits, including tailwinds, should be evaluated. This evaluation should include
maneuvers with rapid power changes. Recirculation of exhaust gases can be critical.
Particular attention should be given to flight and operating conditions that can be judged
critical from review of data on engine inlet pressure and temperature distribution
patterns and engine stall margin data. Operating at high density altitudes, especially
engine operation during low-speed rearward flight, is more likely to result in
unacceptable engine inlet thermal distortion due to reingestion of exhaust gas.
Behavior of the compressor control bleed air valves, if any, must be carefully checked
by collective oscillations around the shut off or open bleed air valves operating points.
To mitigate the possible risk of power loss, a safe test build up should be considered,
such as a build up in actual wind conditions before progressing to rearward or sideward
flight.

               (2) Checks in forward stabilized flight.

                        (i) Behavior of the engine must be checked during level flight, climb,
and descent at various power settings in order to verify the:

           (A) Governing stability (e.g., absence of engine parameters oscillations).


                                                     Page E – 26.1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →