FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-134

PDF page 409 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 409
AC 27-1B · D-134Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (3) Section 27.1583(c) concerns Rotorcraft Flight Manual instructions and
information about removable ballast or loading information. The instructions must be
included in the operating limitations section of the flight manual to allow ready
observance of the limitations.

     b. Procedures.

         (1) The ballast installation may be substantiated by analysis or by static test.
The design ultimate load may be derived from flight, landing, or minor crash conditions
load factors specified in the rules. Substantiation by analysis will require use of the
fitting factor prescribed by § 27.625 where appropriate.  If static tests are to be
conducted, a test plan should be prepared, submitted for evaluation, and agreed upon
prior to the test.

         (2) Ballast installations in the aft part of the fuselage and tail boom may be
subject to significant landing condition angular inertia load factors as well as the usual
linear load factors.

         (3) Substantiation methods and procedures acceptable for the airframe
substantiation may be used for the ballast installation as well.

         (4) Removable ballast will require attention to ensure the ballast is secured
easily and properly and will remain secured under the appropriate ballast design load
factor requirements. The flight manual instructions should be evaluated for compliance
with § 27.1583(c) by flight test and airframe personnel.

         (5) The installation must be designed and placarded or marked for the
maximum allowable ballast load and for other appropriate loading limits. Normally
compliance with § 27.1541 is accomplished with a drawing review by airframe
personnel along with a MIDO or FSDO compliance and conformity inspection. An
additional compliance inspection by airframe personnel can be conducted if desired.





Page D - 134

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →