Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
SUBPART D - DESIGN AND CONSTRUCTION
MISCELLANEOUS
AC 27.871 § 27.871 LEVELING MARKS.
a. Explanation. Reference marks are required for leveling the rotorcraft on the
ground. These marks are necessary for accurate determination of weight and balance
effects, particularly after modifications to the basic rotorcraft.
b. Procedures.
(1) Reference marks are sometimes provided in pairs, one high in the cabin
and one low. The plumb weight is suspended from the high mark by an appropriate
mechanical attachment, and the lower mark is used to level the rotorcraft by centering
the plumb weight. The lower reference mark should be a raised or depressed target
symbol and shall be applied to a permanent structural component or permanently
attached plate in a readily accessible location. Seat tracks, floors, or door sills which
are attached with permanent fasteners are typical locations.
(2) Horizontal reference marks, for support of bubble levels, may also be used,
particularly for smaller rotorcraft.
AC 27.873 § 27.873 BALLAST PROVISIONS.
a. Explanation.
(1) This rule requires that ballast provisions prevent inadvertent ballast shifting
while in flight or as a result of a landing. Shifting of the ballast may cause a hazardous
change in the center of gravity thereby affecting rotorcraft controllability.
(2) Other rules noted here allow removable and fixed ballast and require
markings or placards to prevent overloading the ballast installation.
(i) Section 27.29 specifies that the rotorcraft empty weight will include
any fixed ballast. Section 27.31 allows the use of removable ballast to comply with the
flight requirements. However, ballast may not be adjusted (moved, reduced, or
increased) in flight.
(ii) Section 27.1541 requires conspicuous and durable markings or
placards. Section 27.1557 requires placards stating allowable maximum weight,
distributed loading, if necessary, and other appropriate limitations for ballast installation.
Page D - 133
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.