FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 406

PDF page 406 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 406
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                       AC 27-1B, Chg 7


       (12) Section 27.865(e) External Loads Placards and Markings. Placards and
markings should be installed next to the external load attaching means, in a clearly
noticeable location, that state the primary operational limitations - specifically including
the maximum authorized external load. Not all operational limitations need be stated on
the placard (or equivalent markings) only those clearly necessary for immediate
reference in operations. Other more detailed operational limitations of lesser immediate
importance should be stated either directly in the RFM or in a RFMS.

       (13) Other Considerations.

               (i) Agricultural Installation (AI). AIs can be approved for either jettisonable or
non-jettisonable NHEC or HEC operations as long as they meet relevant certification
and operations requirements and follow appropriate compliance methods. However,
most current AI designs are external fixtures (see definition) - not external loads.
External fixtures are not approvable as jettisonable external cargo because they do not
have a true payload (see definition), true jettison capability (see definition), or a
complete QRS. Many AI designs can dump their solid or liquid chemical loads by use of
a "purge port" release over a relatively long time period (i.e., greater than 30 seconds).
This is not considered true jettison capability (see definition) since the external load is
not released by a QRS and since the release time span is typically greater than
30 seconds (see paragraph c.(21)). Thus, these types of AIs should be approved as a
non-jettisonable external load. However, other designs that have the entire AI (or
significant portions thereof) attached to the rotorcraft, that have short time frame jettison
(or release) capability provided by a QRS that meets the definitions herein and that
have no post-jettison characteristics that would endanger continued safe flight and
landing may be approved as a jettisonable external load. For example, if all the relevant
criteria are properly met, a jettisonable fluid load can be approved as a NHEC external
cargo. Section AC 27 MG 5 of this AC discusses other AI certification methodology.

                (ii) External Tanks. External tank configurations that have true payload (see
definition) and true jettison capability (see definition) should be approved as jettisonable
NHEC. External tank configurations that have a true payload capability but do not have
true jettison capability should be approved as non-jettisonable NHEC. An external tank
that has neither a true payload capability nor true jettison capability is an external
fixture; it should not be approved as an external load under § 27.865.  If an external
tank is to be jettisoned in flight, it should have a QRS that is approved for the maximum
jettisonable external tank payload and is either inoperable or is otherwise rendered
reliable to minimize inadvertent jettisons above the maximum jettisonable external tank
payload.

                 (iii) Logging Operations. These operations are very susceptible to low-cycle
fatigue because of the large loads and relatively high load cycles that are common to
this industry.  It is recommended that load-measuring devices (such as load cells) be
used to assure that no unrecorded overloads occur and to assure that cycles producing
high fatigue damage are properly considered. Cycle counters are recommended to


                                                       Page D – 132.1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →