Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 7 2/4/2016
classes are designated within operational approval under Part 133 and require an
approved rotorcraft-load combination flight manual under § 133.47.
(19) Spider. A spider is a system of attaching a lowering cable or rope or a
harness to a NHEC (or HEC) RLC to eliminate unwanted flight dynamics during
operations. A spider usually has four or more legs (or load paths) that connect to
various points of a PCDS to equalize loading and prevent spinning, twisting, or other
undesirable flight dynamics.
(20) True jettison capability. The ability to safely release an external load using
an approved QRS in 30 seconds or less.
Note: In all cases, a PQRS should release the external load in less than 5 seconds.
Many PQRSs will release the external load in milliseconds, once the activation
device is triggered. However, a manual BQRS, such as a set of cable cutters,
could take as much as 30 seconds to release the external load. The 30 seconds
would be measured starting from the time the release command is given and
ending when the external load is cut loose.
(21) True payload capability. The ability of an external device or tank to carry a
significant payload in addition to its own weight. If little or no payload can be carried,
the external device or tank is an external fixture (see definition).
(22) Type inspection authorization (TIA). This is FAA Form 8110-1, used for
authorizing official ground inspections and flight-tests necessary to fulfill the
requirements for type certification or supplemental type certification. Order 8110.4
contains the criteria for TIA issuance.
(23) Winch. A device that can employ a cable and drum or other means to exert
a horizontal (i.e., x-rotorcraft axis) pull. However, in designs utilizing a winch to perform
a hoist function by use of a 90-degree cable direction change device (such as a pulley
or pulley system), the winch system is considered a hoist and must comply with the
hoist requirements.
d. Procedures. The following certification procedures are provided in the most
general form. Where there are significant differences between the cargo types, these
differences are highlighted.
(1) General Compliance Procedures for § 27.865. The applicant should clearly
identify both the applicable cargo types (NHEC or HEC) and the jettison capability
(jettisonable or non-jettisonable) for which application is being made. The structural
loads and operating envelopes for each applicable cargo type should be determined
and used to formulate the flight manual supplement and basic loads report. The
applicant should show by analysis, test, or both, that the rotorcraft structure, the
external load attachment means, and the PCDS, if applicable, meet the specific
Page D - 114
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.