Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
4/25/06 AC 27-1B, Chg 2
any other rig/ground test facility shown to be representative. The demonstration should
show that floats do not impede a satisfactory evacuation. Service experience has
shown that it is possible for occupants to have escaped from the cabin but have not
been able to board a liferaft and have had difficulties finding handholds to stay afloat
and together. Where practical, handholds or lifelines should be provided. The normal
attitude of the rotorcraft and the possibility of a capsize should be considered when
locating the handholds or lifelines.
(6) Rotorcraft Flight Manual. The Rotorcraft Flight Manual is an important
element in the approval cycle of the rotorcraft for ditching. The material related to
ditching may be presented in the form of a supplement or a revision to the basic
manual. This material should include:
(i) The information pertinent to the limitations applicable to the ditching
approval should include the range of sea state conditions that has been demonstrated
for water entry and flotation stability. If the ditching approval is obtained in a segmented
fashion (i.e., one applicant performing the aircraft equipment installation and operations
portion and another designing and substantiating the liferaft/lifevest and ditching safety
equipment installations and deployment facilities), the RFM limitations should state “Not
Approved for Ditching” until all segments are completed. The requirements for a
complete ditching approval not yet completed should be identified in the “Limitations”
section.
(ii) Procedures and limitations for flotation device inflation.
(iii) Recommended rotorcraft water entry attitude, speed, and wave
position.
(iv) Procedures for use of emergency ditching equipment.
(v) Procedures for ditching egress and raft entry.
(vi) Information stating the flotation system has been certificated for
Ditching (as opposed to Emergency Flotation) to facilitate compliance with operational
requirements.
Page D - 89
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.