FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 310

PDF page 310 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 310
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/2008                                      AC 27-1B, Chg 3

AC 27.681.  § 27.681 LIMIT LOAD STATIC TESTS.

     a. Explanation.

         (1) The rule requires static tests of the control system in showing compliance
with limit load requirements.

         (2) The tests are specified to include each fitting, pulley, and bracket of the
control system being tested and to include the “most severe loading.”

         (3) Also, the rule requires that compliance with bearing factors
(reference § 27.623) be shown by individual tests or by analyses for control system
joints subject to motion.

     b. Procedures.

         (1) Compliance with the requirements of this rule is obtained by static tests
conducted on either a static test airframe or on a prototype flying ship. In either case,
conformity of the control system and related airframe is necessary to validate the tests.

         (2) The rotor blades or aerodynamic surfaces may be used to react pilot effort
loads through the control system, or they may be replaced with fixtures.  If fixtures are
used, they should be evaluated for geometric and stiffness efforts to ensure test validity.

         (3) The loads to be applied during the limit load static tests are specified in
§§ 27.395, 27.397, and 27.399. The loads are applicable to collective, cyclic, yaw, and
rotor blade control systems as well as any other flight control systems provided by the
design.

         (4) Although Part 27 does not explicitly specify the bearing factors to be used in
control system rotating joint tests or analyses, the factors of § 29.685 have been used in
past programs. These factors are 3.33 for push-pull systems and 2.0 for cable systems
for joints with plain bearings and manufacturers’ ratings for ball and roller bearings.


                [The remainder of this page intentionally left blank.]





                                                     Page D – 40.1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →