Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
SUBPART D - DESIGN AND CONSTRUCTION
ROTORS
AC 27.653 § 27.653 (Amendment 27-2) PRESSURE VENTING AND
DRAINAGE OF ROTOR BLADES.
a. Explanation. The rule requires each rotor blade to be provided with venting
and drainage means (i.e., holes, etc.) or else the blade must be sealed and designed to
withstand internal pressure.
b. Procedures. Although the rule provides for venting and drainage features,
recently certificated blades have been designed to be sealed and to sustain the
“maximum pressure differentials expected in service.” For modern blade designs, the
internal pressure buildup due to environmental effects and centrifugal acceleration
effects (near the tip) can be readily sustained with moisture sealing accomplished. The
use of sealed blades is highly advantageous and recommended because of the
possibility for severe corrosion damage resulting from trapped moisture and because of
the difficulty in finding internal corrosion damage by use of field level inspections.
AC 27.659 § 27.659 (Amendment 27-2) MASS BALANCE.
a. Explanation. The rule requires that mass balancing of rotors and blades be
provided, as necessary, to prevent excessive vibration and flutter. Further, the rule
requires structural substantiation of the mass balance installation.
b. Procedures.
(1) The weight, geometry, and location of rotor and blade mass balance
devices are determined as the requirements of §§ 27.571 and 27.629 are met.
(2) The structural substantiation should show static strength to meet the
maneuver and gust loads of §§ 27.337, 27.339, and 27.341. In addition, the main rotor
loads of § 27.547(c) should be substantiated. The fatigue strength of the mass balance
devices (including structural supports) should meet the requirements of § 27.571.
(3) In addition to the appropriate strength requirements, some recent designs
have included features which trap the balance weight inside a limited area even if the
primary attachment means (adhesive, bolts, etc.) fail. This type of design feature is
recommended because of the severe loading environment to which balance devices are
subjected.
AC 27.661 § 27.661 (through Amendment 29-2) ROTOR BLADE CLEARANCE.
a. Explanation.
Page D - 31
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.