FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-78

PDF page 228 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 228
AC 27-1B · C-78Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03

restraining the upper torso, the total strap tension load does not exceed 8.90kN (2,000
lbs).
               (vi)  The maximum compressive load measured between the pelvis and
the lumbar column of the (ATD) does not exceed 6.67 kN (1,500 lbs.).

                (vii)  Each upper torso restraint strap remains on the ATD shoulder during
impact.

                 (viii) The pelvic restraint remains on the ATD pelvis during impact.

        f.  Procedures for Evaluating Impact Pulse Shapes.

         (1) Acceptable Evaluation Method. Data for evaluating the impact pulse shape
are obtained from an accelerometer which measures the acceleration on the test fixture
or sled at the seat location or equivalent location in the direction parallel to the line of
inertial response shown in Figure 27.562-1 of this guidance. The impact pulses
intended for the tests discussed in this guidance have an isosceles triangle shape.
These ideal pulses are considered minimum test conditions. Since the actual acquired
test pulses will normally differ from the ideal, it may be necessary to evaluate the
acquired test pulses to insure the minimum requirements are satisfied.

         (2) An acceptable method to evaluate the pulse shape should use the following
steps:

                  (i)   Extend the calibration baseline (zero G)

                   (ii)   Locate the maximum peak deceleration (Gp) indicated on the plot.

                    (iii)   Construct reference lines parallel to the baseline at levels of 0.1 Gp,
0.9 Gp, and 1.0 Gp.

               (iv)   Construct an onset line through the intersection points of the 0.1 Gp
and 0.9 Gp reference lines with the increasing (onset) portion of the data plot. The data
plot should not return to zero G between the two points selected.

              (v)   Locate the intersection points of the onset line with the baseline and
with the 1.0 Gp reference line. The interval between these two points, measured along
the time axis of the data plot, is considered the rise time (tr) of the test impact pulse.

               (vi)  The rise time of the test impact pulse should not exceed the value of
(tr) given in Figure AC 27.562-1 for each test.

                (vii)  The area under the data plot curve within the rise time of the test
impact pulse, Vra, should represent at least one half of the impact velocity given in
Figure AC 27.562-1 for each test.  If the value of peak acceleration measured in the test



Page C - 78

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →