Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
deformation at the sidewall attachment during a landing impact. (See Figure 27.562-3
for a schematic of an installation.)
(5) Seats that are cantilevered from one sidewall without connection to
another structure would not be subject to floor deformation. However, sidewall
deformation is likely, and should be considered by warping the entire sidewall
attachment plane, or the attachment points of the seat, 10° to represent the most likely
fuselage sidewall deformation. This is intended to evaluate a critical condition for seat
attachment or seat and occupant restraint system performance. Either a rigid sidewall
simulation or an actual sidewall panel may be used. If a rigid sidewall simulation is
used, the test fixture should transfer loads to the seat through components equivalent to
the attachment fitting as well as the surrounding sidewall to replicate the actual
installation.
(6) Side-facing seats, occupiable for takeoff and landing, are subject to
the specified dynamic test conditions. Compliance with the structural requirements
should be demonstrated for side-facing seats using the same conditions for the test and
pass/fail criteria as for fore- and aft-facing seats. The seat should be loaded in the most
critical case structurally. Means of restraining the ATDs may need to be adapted to
ensure adequate retention during the test. The application of floor distortion will need to
be assessed on an individual basis, depending on the design and the method of
attaching the seat.
(7) A seat assembly for multiple occupants may have more than two pairs
of legs. If the assembly uses a uniform cross section, deformation of only the outer leg
assemblies is sufficient. The inner leg pairs may be maintained in the normal,
undeformed position for the dynamic tests.
(D) Multiple Row Test Fixtures. In tests of passenger seats normally
installed in rows in a rotorcraft, head impact conditions should be evaluated by tests
using at least two rows of seats. This allows direct measurements of the head injury
data if secondary head impact occurs and demonstrates the effect of the interaction
loads between rows; e.g., due to occupant contact with the front row. (That is, ATD leg
contact does not overload the front row.) These conditions are usually critical only on
Test 2. The single seat row fixture used for the test should be used to position the front
(first) seat row and provide appropriate floor deformation to that row. The test is critical
for the first row strength. An additional simple fixture may position the second seat row
in the proper location and need not provide floor deformation. The second row should
be fully occupied unless it is not as critical a condition for the first seat row.
Representative seat cushions and torso restraint systems should be used on both seat
rows. The allowable seat pitch (longitudinal spacing) can be determined by analysis of
previous test data or limited by type design data and information for the most critical
condition for head or leg impact against relatively stiff structure in the first seat row.
Operational limitations that specify the allowable seat pitch of the seats in rotorcraft may
be considered also. No impact surface such as seats, bulkheads, etc., may be needed
Page C - 56
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.