FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-55

PDF page 205 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 205
AC 27-1B · C-55Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

             (C) Alternative configurations. The preceding discussion described the
fixture and floor deformation procedure that would be used for a typical seat that has
four seat legs and four attachments to the fuselage floor. These test procedures may
be adapted to seats having other designs. Special test fixtures may be necessary for
different configurations. The following methods, while not covering all possible seat
designs, provide guidance for the more common configurations of seats:

               (1) Rotorcraft seats with three legs may have one central leg in front or
back of the seat and one leg on each side of the seat. The central leg should be held in
its undeformed position as pitch deformation is applied to one side leg and roll to the
other.

               (2) Seats that are “integral” with the structure without floor or sidewall
attachment devices and with continuous attachments such as rows of rivets or screw,
etc., are excluded from the deformation, misalignment, or preload prior to test impact.
Similarly bulkhead-mounted seats, solely mounted to a bulkhead, are excluded from the
deformation requirement. The test fixture could represent the seat and structure or a
rigid bulkhead or an actual bulkhead panel.  If a rigid bulkhead installation is used, the
test fixture should transfer loads to the seat restraint system through components
equivalent to the seat attachment fittings and surrounding bulkhead panel, which exist in
the actual installation. Similar guidelines apply to integral seats.

               (3) Seats that are attached to both the floor and a bulkhead would be
tested on a fixture that positions the bulkhead surface in a plane through the axis of
rotation of the pitch beam. The bulkhead surface should be located perpendicular to the
plane of the floor (the rotorcraft floor surface, if one were present) in the undeformed
condition or in a manner appropriate to the intended installation. Either a rigid bulkhead
simulation or replica or an actual bulkhead panel may be used.  If a rigid bulkhead
simulation is used, the test fixture should transfer loads to the seat restraint system
through components equivalent to the attachment fitting and surrounding bulkhead
panel that would exist in the actual installation. The seats would be attached to the
bulkhead and the floor in a manner representative of the rotorcraft installation, and the
floor, as represented in the test, would then be deformed as described in
paragraph b(2)(ii)(B).

               (4) Seats mounted between fuselage sidewalls or to the sidewall and floor
of an airplane should be tested in a manner simulating rotorcraft fuselage cross-section
deformation (e.g., from circular or rectangular to flattened circular or rectangular or
ellipsoidal shape) during a severe impact. The 10° roll would simulate the change in
fuselage shape. Brackets should be fabricated to attach the seat to the sidewall test
fixture at the same level above the fixture “floor” that would represent the installation
above the rotorcraft floor. The sidewall bracket or rail should be located on the “roll”
beam.  It is envisaged that the sidewall rolls outward 10° about an axis at the floor and
sidewall juncture. Then, as the beams are rotated to produce the critical loading
condition, the combined angular and translational deformation would simulate the



                                                          Page C - 55

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →