Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
SUBPART C - STRENGTH REQUIREMENTS
MAIN COMPONENT REQUIREMENTS
AC 27.547 § 27.547 (Amendment 27-3) MAIN ROTOR STRUCTURE.
a. Explanation. This regulation requires the main rotor structure to be designed to
the static load requirements of §§ 27.337 through 27.341 (vertical maneuvering loads
and vertical and horizontal gust loads). In addition, the main rotor blades, hubs, and
flapping hinges are specified to be designed for impact forces of each blade against its
stop during ground operation and for specified limit torque at any rotational speed
including zero. The torque forces (from the drive system) are distributed to the rotor
blades as specified.
b. Procedures.
(1) Substantiation in compliance with this standard is accomplished by
application of the flight loads of §§ 27.337 through 27.341 and the torque loads of
§ 27.361 to the rotor structure by stress analyses and/or static tests. The use of wind
tunnel data as well as flight loads survey data may be used to generate and/or check
the external load magnitudes and distributions.
(2) Where new materials are used in the main rotor structure, such as
composites containing plastics, the effects of temperature and humidity are to be
considered in accordance with § 27.603, and the effects of uncertainties in
manufacturing processes or inspection methods are to be considered in accordance
with § 27.619. More experience is available for metallic materials, but § 27.603 requires
that metallics be suitably protected against the effects of environmental conditions.
(3) The design impact forces of each blade must be imposed against its stop or
stops. Appropriate monitoring of the blades, hubs, flapping hinges, and stops during
laboratory tests, ground endurance tests, and flight tests should ensure that the stops
are sufficient for ground operation loads. The design torque loads are derived as
prescribed.
AC 27.549 § 27.549 (Amendment 27-3) FUSELAGE, LANDING GEAR, AND
ROTOR PYLON STRUCTURE.
a. Explanation. This regulation requires that the fuselage, landing gear, and rotor
pylon (including the tail fin, if any) be designed to withstand the flight loads of §§ 27.337
through 27.351, the ground loads of §§ 27.235, 27.471 through 27.497, skid loads of
§ 27.501, ski loads of § 27.505, water loads of § 27.521, and rotor loads of § 27.547(d)
and (e). The ski and water loads pertain to optional features. Consideration is also
required of –
Page C - 38
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.