FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-28

PDF page 178 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 178
AC 27-1B · C-28Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

             SUBPART C - STRENGTH REQUIREMENTS

                     GROUND LOADS


AC 27.471  § 27.471 GROUND LOADS--GENERAL.

     a. Explanation. This regulation specifies that limit ground loads must be
considered which are:

         (1) External loads caused by landing (ground) conditions for skid and wheel
landing gear equipped rotorcraft and by ground taxiing loads as specified in § 27.235 for
wheel landing gear equipped rotorcraft.

         (2) Loads considering the rotorcraft structure as a rigid body.

         (3) Loads in equilibrium with linear and angular inertia loads.

         (4) The critical center of gravity “must be selected so that the maximum design
loads are obtained in each landing gear element.”

     b. Procedures.

         (1) The standards to be considered are specified in §§ 27.473 through 27.505.
These associated standards cover landing gear arrangements, landing conditions, and
ground loading conditions (for wheel landing gear rotorcraft).

         (2) Drop tests may be used to verify landing load factors. (See
paragraph AC 27.725.)

         (3) The application of the design loads derived from the landing load factors will
be as specified for each element affected by landing or ground loading conditions (for
wheel landing gear rotorcraft).

         (4) During the applicant’s flight test program, the landing load factors for skid
and wheel landing gear rotorcraft and taxiing load factors for wheel landing gear
rotorcraft are monitored to assure the design load factors used are adequate. See
paragraph AC 27.235 of this document for § 27.235 policy.

AC 27.473  § 27.473 (Amendment 27-2) GROUND LOADING CONDITIONS AND
          ASSUMPTIONS.

     a. Explanation. The rotorcraft is to be designed for the maximum weight. A rotor
lift of two-thirds of the design maximum weight may be used. The minimum limit landing
load factor is determined by the drop tests of § 27.725.



Page C - 28

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →