FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-5

PDF page 155 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 155
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


             SUBPART C - STRENGTH REQUIREMENTS

                           FLIGHT LOADS


AC 27.321  § 27.321 (Amendment 27-11) FLIGHT LOADS--GENERAL.

     a. Explanation.

         (1) The rule specifies the way the loads will be applied to the rotorcraft.  It
requires load analysis from minimum to maximum design weight. Any practical
distribution of disposable loads must be included in the analysis.

         (2) Paragraph (a) of the rule states: “The flight load factor must be assumed to
act normal to the longitudinal axis of the rotorcraft, and to be equal in magnitude and
opposite in direction to the rotorcraft inertia load factor at the center of gravity.”

     b. Procedures.

         (1) Derivation of the flight loads is required by and specified in §§ 27.337
through 27.351. This rule requires flight load determination from minimum to maximum
weight and for disposable loads.

         (2) The application of the design loads derived from the flight load factor will be
as specified. The flight loads analysis data must comply with the rule.

AC 27.337  § 27.337 (Amendment 27-26) LIMIT MANEUVERING LOAD FACTOR.

     a. Explanation. The rotorcraft must be designed and substantiated to load factors
as specified to provide a minimum level of structural integrity of the rotorcraft airframe
and rotors.

         (1) A range of design positive load factors from +3.5 to +2.0 may be used.

         (2) A range of design negative load factors from -1.0 to -0.5 may be used.

         (3) Load factors inside the range of +3.5 to -1.0 may be used provided the
probability of exceeding the design load factors is shown by analysis and flight tests to
be extremely remote and the selected load factors are appropriate to each weight
condition between design maximum and minimum weight.

         (4) Load factors exceeding these “minimums” may be used.

     b. Procedures.



                                                           Page C - 5

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →