Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(2) Whenever tests are used or required, a test proposal or plan should be
approved prior to the tests. The test article should have received conformity inspections
and should have been accepted by the FAA/AUTHORITY for the test. Test fixtures and
instrumentation should also be acceptable to the FAA/AUTHORITY (using DERs as
appropriate) prior to the start of the test. The quality control office of the applicant or
other qualified personnel may be authorized to conduct inspections of the test fixtures
and instrumentation rather than the FAA/AUTHORITY or DER performing this task. The
test proposal may be used to define and to authorize the means to accomplish
inspection of the test fixtures and instrumentation. Unnecessary drawings such as test
fixture details or layering of approvals are not intended or envisaged by this policy.
Drawings, sketches, or photographs have been used by the FAA/AUTHORITY to
control and to ensure correct location, direction, and magnitude of loads and other
critical test parameters.
(3) Structural analysis has been accepted for rotorcraft in place of static tests.
Generally, the rotorcraft airframe should have natural frequencies remote to
predominant rotor excitation sources, including higher harmonics, to avoid undesirable
and possibly excessive vibration and potentially high operating stress levels due to this
vibration. During the flight load measurement program conducted under § 27.571,
critical loaded areas or critical joints may be instrumented with strain gages or other
stress strain measuring devices. This actual flight data should be compared to the
analytical data to verify accuracy.
(4) Paragraph (b) of the rule specifies certain tests. Test proposals should be
approved prior to conducting official FAA/AUTHORITY tests. Other paragraphs in this
advisory circular pertain to those tests.
AC 27.307A. § 27.307 (Amendment 27-26) PROOF OF STRUCTURE.
a. Explanation. Amendment 27-26 adds the requirement to account for the
environment to which the structure will be exposed in operation. This change is
intended to codify recent FAA/AUTHORITY and industry practices for the consideration
of environmental effects in showing “proof of structure.”
b. Procedures. All of the policy materials pertaining to this section remains in
effect with the following additions:
(1) For either tests or an analysis, environmental effects are now explicitly
required. Consideration of loss of strength and stiffness of metals with elevated
temperatures and loss of strength and stiffness of composite materials from exposure to
heat, moisture, or other operational environments is now required and should be
documented in analyses and test reports.
(2) MIL-HDBK-5F; AC 20-107B; or MIL-HDBK-17, Vol. I, Rev 1E; Vol. II,
Rev. D; Vol. III, Rev E (or later versions) are acceptable sources of data and procedures
Page C - 1
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.