Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/17/2009 AC 27.1B, Chg4
excessively inaccurate at about 10° of sideslip. Rapidly yawing to the desired sideslip
angle and noting and maintaining the new “standard” indicated airspeed may give
adequate data. Control positions (directional as a minimum), sideslip angle, rotorspeed,
airspeed, rate of descent, amount of ball deflection, and bank angle should be recorded.
The pilot should note the physical sideforce feel experienced. The rule requires that
sufficient cues accompany sideslip to alert the pilot when approaching sideslip limits. A
minimum of two sideslip data points on each side of the trim point should be obtained to
adequately define the slope of the pedal displacement versus sideslip angle
relationship.
(v) Static directional stability plots can be expected to differ slightly on either side of
the inherent sideslip angle. Positive static directional stability is indicated by increased left pedal
displacement for a larger right sideslip and, conversely, increased right pedal for a larger left
sideslip angle.
AC 27.177A. § 27.177 (Amendment 27-44) Static Directional Stability.
a. Explanation. Amendment 27-44 makes an extensive change to the current
requirement and provides for a clear definition of the sideslip envelope to be evaluated.
Most rotorcraft exhibit satisfactory quantitative and qualitative directional characteristics
except for the first 2-3 degrees either side of trim due to inherent airflow blockage of the
vertical fin or tail rotor. This amendment takes this blockage into account while
requiring that positive directional stability is maintained at larger sideslip angles. The
actual demonstration has been increased from a maximum range of ±10° at all speeds,
as the previous amendment requires, to ±25° at slow speeds and linearly decreasing to
±10° at VNE. Alternatively to the previous range specified, the requirement limits the
maximum sideslip to be demonstrated to at least 0.1g of sideforce or the maximum
sideslip attained when full directional control is applied. As in the previous amendment,
sufficient cues should alert the pilot when approaching sideslip limits.
b. Procedures. The policy material pertaining to the procedures outlined in this
section remain in effect.
Page B – 60.7
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.