Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27.1B, Chg4 3/31/2014
AC 27.177. § 27.177 (Amendment 27-21) STATIC DIRECTIONAL STABILITY.
a. Explanation. This rule requires that positive static directional stability be
demonstrated at the trim airspeeds defined in § 27.175. The trim speed for climb is VY
and for cruise 0.9VH or 0.9VNE (whichever is less).
b. Procedures.
(1) Tests for static directional stability require instrumentation for pedal position
and sideslip angle. To obtain accurate sideslip angle and airspeed information, a “yaw
boom” is usually installed for the purpose of mounting a sideslip vane and swiveling
airspeed pilot head outside the main rotor downwash region of influence. Special care
should be taken to ensure that the yaw boom installation has been verified to be
structurally adequate and free of dynamic instabilities for all combinations of airspeed
and rotor speed likely to be experienced during the static directional evaluation. For
some installations, the instrumentation yaw boom may influence the flying qualities of
the rotorcraft itself. Thus, it is advisable to correlate yaw string displacement or slip
indicator ball widths of skid with yaw boom sideslip angle, and then repeat a few critical
points with the yaw boom removed.
(2) For some rotor system designs, the main and tail rotor flapping angle may
be a critical instrumentation requirement for static directional testing. Both main and tail
rotor flapping may increase dramatically at high airspeeds with increasing sideslip
angle. Therefore, for rotor systems exhibiting this characteristic, flapping should be
monitored carefully during the sideslip maneuver to avoid exceeding limitations. Static
directional stability is normally defined in terms of pedal displacement required to
maintain a steady heading sideslip. A single-rotor rotorcraft flying in coordinated flight
will exhibit a small inherent sideslip due to tail rotor thrust and fuselage/main rotor
sideforces. This condition is normally taken as trim with the inherent sideslip angle
noted. Airspeeds should be the trim values described above. The procedures used to
establish and maintain the steady heading sideslip can significantly influence test
results. A generally accepted technique follows:
(i) Stabilize at the trim point, and note indicated airspeed.
(ii) Record trim conditions including inherent sideslip. Maintain fixed
collective and throttle for the remainder of the maneuver.
(iii) Smoothly apply directional control and coordinate with lateral control
to establish the desired sideslip angle. A steady track can best be ensured by
maintaining a track over a straight landmark on the ground such as a section line or
straight segment of powerline or highway.
(iv) Because drag increases with sideslip, the aircraft will decelerate. The
trim airspeed should be maintained by entering a slight dive or decreased rate of climb.
If a boom airspeed system is not used, a “standard” airspeed system will become
Page B – 60.6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.