FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 134

PDF page 134 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 134
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/17/2009                                      AC 27.1B, Chg4


by an offsetting arm in such a manner that it can be pushed down on the board to
record relative cyclic position at key times during test maneuvers. The Figure AC
27.175A-1 plot is a typical presentation of longitudinal static stability.

                   (ii) Other necessary parameters include pitch attitude, pressure altitude,
ambient temperature, and indicated airspeed.

         (2) Ambient Conditions. Smooth air is necessary for stability testing.

         (3) Loading. Aft center of gravity (CG) is ordinarily critical for longitudinal
stability testing, although high-speed flight should be checked at full forward CG and
maximum weight. At aft CG, light or heavy weight conditions can be critical. The
manufacturer’s flight data should be reviewed to determine critical loading conditions.

         (4) Conducting The Test.

                  (i) The rotorcraft should be established in the desired configuration and
flight condition (climb, cruise, VNE, autorotation) with the required power and rotor speed
at the trim airspeed. The collective stick should be fixed in that position: usually by
applying sufficient friction to ensure that it is not inadvertently moved. For autorotative
tests, a rotor speed should be selected so that the variations in rotor speed as airspeed
and altitude change do not exceed the allowable limits. This point is recorded as the
trim point. Airspeed is then increased or decreased in about 5-knot increments,
stabilizing on each speed and recording the data. At least two points on each side of
the trim speed should be taken.

                   (ii) The cruise test should be conducted by varying airspeed around the
desired altitude with throttle and collective fixed. This should be accomplished by first
determining VH (level flight speed at maximum continuous power) at the test altitude.
Then adjust power to establish a level trimmed condition at VH (or 0.8 VNE if lower). This
point is then recorded as the trim point.

                    (iii) For climb and autorotation tests, conduct fixed collective tests through
an altitude band (usually ±2,000 feet).  It will probably not be possible to obtain the
required data on one pass through the altitude band. If repeated passes are required, a
trim point should be taken at the beginning of each pass unless very sensitive collective
pitch position information is available in the cockpit.

               (iv) If extremely precise results are required, an alternate method of testing
can be used to acquire the data at a constant altitude. For cruise and VNE, data can be
obtained by alternating airspeeds above and below the trim speed to arrive in the
vicinity of the test altitude as the point is recorded. This method results in very precise
data because collective and throttle are not moved as airspeed is changed at a constant
altitude. A typical sequence of speeds that could produce these results would be: 140
(0.8 VNE) trim speed, 135, 145, 130, and 150.



                                                        Page B – 60.3

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →