Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27.1B, Chg4 9/17/2009
AC 27.175A. § 27.175 (Amendment 27-44) DEMONSTRATION OF STATIC
LONGITUDINAL STABILITY.
a. Explanation. Amendment 27-44 reduces the speed range for the climb and
cruise demonstration points of §§ 27.175(a) and 27.175(b), respectively. A new
paragraph (c) was added to require an additional cruise demonstration point in order to
compensate for the change in reduced speed range in paragraph (b). Additionally, for
autorotation, two typically used trim points are required in place of the current
requirement. The requirement for the hover demonstration was eliminated for the
reasons given in AC 27.173 (Amendment 27-44).
All the policy material pertaining to this section remains in effect with the following
changes:
(1) This rule incorporates the specific flight requirements for demonstration of
static longitudinal stability. Specific loadings, configurations, power levels, and speed
ranges are stated for conditions of climb, cruise, VNE, and autorotation.
(2) Some rotorcraft in forward flight experience significant changes in engine
power with changes in airspeed even though collective and throttle controls are held
fixed and altitude remains relatively constant. For these cases, the guidance in
§ 27.173, which states that throttle and collective pitch must be held constant, is
appropriate for administration of this rule, and the specified powers in § 27.175 should
be considered as power established at initial trim conditions. This will result in slightly
higher or lower power readings at “off trim” conditions. Collective and throttle controls
are held constant when obtaining test data.
(3) The effects of rotor RPM on autorotative static stability should be
determined and positive stability demonstrated for the most critical RPM. For Category
A rotorcraft this requirement may be satisfied at a nominal RPM value. RPM values can
be expected to change as airspeed is varied from the “trimmed” condition. The
manufacturer’s recommended autorotation airspeed is ordinarily used for trim.
b. Procedures.
All the policy material pertaining to this section remains in effect with the following
changes:
(1) Instrumentation.
(i) Sensitive control position instrumentation is mandatory. Engine power
parameters should be recorded at trim. For testing of minor modifications or when
using a “before and after” method, a tape measure or a stick plotting board may be
utilized. A stick plotting board consists of a level surface with a clean sheet of paper on
it and attached to the cockpit or seat structure. The installation must not interfere when
the flight controls are fully displaced. A recording pencil is attached to the cyclic control
Page B – 60.2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.