FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 123

PDF page 123 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 123
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


conduct of these tests, all available techniques should be utilized when the pilot finds
himself "out of control." However, compliance with this section requires that recovery
must be shown by use of only the primary control for each axis of aircraft motion.

         (6) Cyclic control authority in autorotation must be sufficient to allow adequate
flare capability and landing under the all-engine-inoperative requirements of § 27.75.

AC 27.151.  § 27.151 (Amendment 27-21) FLIGHT CONTROLS.

   a. Explanation. Excessive breakout or preload in the flight controls produces control
system force discontinuities, which result in increased workload and controllability
problems for the pilot. Similarly, excessive freeplay results in lost motion, which
increases pilot workload and, in an extreme case, could lead to a hazardous pilot-
induced oscillation. In some designs friction can provide a positive contribution to the
function of the flight controls (e.g., masking aerodynamic feedback in reversible
systems). At some point, friction will have a detrimental effect on the pilot’s ability to
properly control the rotorcraft. In the case of an irreversible design equipped with an
artificial force feel system in pitch and roll, excessive friction can mask a shallow force
gradient making positive stick centering and control force static stability difficult if not
impossible to demonstrate. In such an instance, the initial choice of fixes might include
implementation of a steeper force gradient or addition of a force preload. Care must be
exercised during the initial design phase to ensure that the components and
characteristics of the flight control system are well matched.

   b. Procedures. Regardless of the flight control system sophistication, it is important
that the test pilot understand the system configuration prior to flight evaluation.
Appropriate mechanical characteristics should be documented. For VFR rotorcraft, the
mechanical characteristics are typically assessed in flight on a qualitative basis.  If a
controllability or workload problem is identified, a more detailed investigation would be
necessary. Since IFR certification rules include specific trim and force requirements, a
more quantitative investigation of mechanical characteristics is normally conducted.
The constantly varying feedback forces of reversible flight control systems generally
make such designs unsuitable for IFR application. Irreversible system mechanical
characteristics can often be partially documented on the ground with external hydraulic
and electrical power supplies connected to the rotorcraft. Characteristics of the flight
control system should be qualitatively considered during other flight tests. These
characteristics include forces, control harmony, nonlinearities, discontinuities, proper
directional senses, breakout, friction, hysteresis, etc.





Page B – 52.8

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →