FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page Apdx A-58

PDF page 1161 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1161
AC 27-1B · Apdx A-58Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                                  2/12/03

                                  MANUAL IDENTIFICATION)
                       ATTACHMENT 2
            INSTRUCTIONS FOR CONTINUED AIRWORTHINESS
                   PROCEDURES INFORMATION
The procedures information in this appendix is not a requirement. It is intended as
guidance to assist the applicant in preparing procedures for Instructions for Continued
Airworthiness (ICA).
An ICA is required when field maintenance personnel are authorized to remove, disassemble,
assemble, clean, inspect, check, repair, replace, install, service, lubricate, test, troubleshoot,
adjust, or apply a protect treatment to a rotorcraft, its engine(s), rotor(s), or appliances.

The following topics should be considered when preparing procedures for an ICA.

     1.  Provide general information about the appliance.

     2.  Provide a description of the appliance in the procedures.

     3.  Specify any necessary precautions to be taken during the procedures and include them
in Notes, Cautions, and Warnings.

     4.  Specify tool(s), special tool(s), or equipment required for the procedures.

     5.  Specify torque value(s) for the appliances and attaching hardware.

     6.  Provide information to gain access to the appliance.

     7.  Consumable Materials should be identified by specification/part number, product name,
or manufacturer.

     8.   Identify the appliance that is to be removed, disassembled, cleaned, inspected, checked,
repaired, replaced, assembled, checked, serviced, tested, adjusted, or operated.

     9.  Develop order and method procedures for removing, and/or replacing the appliance,
including a procedure to protect opening, lines, and hoses, etc., from contamination.

     10. Develop order and method procedures for disassembly and assembly of the appliance,
including any special process required and safety precautions.

     11. Develop order and method procedures for cleaning the appliance, including any special
process(es) to be used during cleaning. Identify type of cleaning materials.

     12. Specify what inspections or checks are required and their interval. Develop order and
method for inspecting the appliance, including special inspection techniques, standards and
limits. Describe what actions are to be taken when appliance is found unacceptable.
REVISION:                                                     (DATE)
Revision 3                                                            Page 1


Page Apdx A - 58

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →