FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page Apdx A-49

PDF page 1152 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1152
AC 27-1B · Apdx A-49Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                          AC 27-1B, Chg 2

                                      (MANUAL IDENTIFICATION)
                       REQUIREMENTS
                                    (Continued)
16. ORDER AND METHOD OF REMOVAL

Information describing the order and method of removal of products and parts with any
necessary precautions to be taken. Reference Appendix A, A27.3 (b)(3). This is required when
products and parts can be removed as part of maintenance. This includes the removal of
products and parts in conjunction with a repair.
   a. The order is a step-by-step procedure: what is the first thing you do, then what is next,
until the product or part is removed.

   b. The method is the procedure or process used to remove the product or part. If the removal
of a product or part could result in injury to personnel or damage to the rotorcraft if not done
correctly, the ICA should include precaution. See Chapter1, Paragraph 13.

   c. The information is normally contained in the chapters requiring removal of the product or
part.

17. ORDER AND METHOD OF REPLACING

Information describing the order and method of replacing products and parts with any
necessary precautions to be taken. Reference Appendix A, A27.3 (b)(3). This is required when
products and parts can be replaced.

   a. The order is a step by step procedure, what is the first thing you do, then what is next until
the product or part is replaced (reinstalled).

   b. The method is the procedure or process used to replace (reinstall) the product or part. If
the replacement of a product or part could result in injury to personnel or damage to the
rotorcraft if not done correctly, the ICA should include precaution. See Chapter1 Paragraph 13.

   c. The use of the phrase “Install in reverse order” does not meet the requirements of the
FAR/JAR and should not be used in the ICA.

   d. The information is normally contained in the chapters requiring replacement of the part.

18. GENERAL PROCEDURAL INSTRUCTIONS -TESTING

General procedural instructions including procedures for system testing during ground run.
Reference Appendix A, A27.3 (b)(4). This is required when system testing during ground run is
specified. The information is normally contained in the chapters requiring the test, or applicant
may have a section for special inspections, tests, and checks.

REVISION:                                         (PAGE NUMBER)
Revision 4                                                                              (  )-00-00 Page 7


                                                                  Page Apdx A - 49

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →